In RC, a channel is one independently controlled function. Each channel carries one signal. That signal might move one servo, set the throttle, or switch something on or off. A simple plane uses four channels for aileron, elevator, throttle, and rudder.
The four primary channels
- Aileron rolls the plane around its long axis. On many planes, the two ailerons move in opposite directions.
- Elevator pitches the nose up or down.
- Throttle sets the motor power.
- Rudder yaws the nose left or right.
Channel order on different radios
Radios assign the four primary functions to channel numbers in a default order. Futaba uses AETR (aileron, elevator, throttle, rudder). Spektrum and JR commonly use TAER (throttle, aileron, elevator, rudder). Radios running EdgeTX can change the order.
Check the channel-assignment screen before you set up a new plane. The order decides which stick controls which function, and a mismatch can be confusing on the first flight.
How many channels different planes need
- 2 channels: typically throttle and rudder, or rudder and elevator, on simple gliders and foam planes.
- 3 channels: rudder, elevator, and throttle, the classic trainer setup.
- 4 channels: adds ailerons for full control of a basic sport plane.
- 5 or more channels: adds functions such as flaps, retracts, gyro gain, flight modes, lights, and drop releases.
Proportional and switch channels
A proportional channel responds across a range of positions, such as a stick, slider, or knob. A switch channel has two or three fixed positions, such as on and off. Landing gear, flight modes, and lights are usually switch channels. Many radios let you set a three-position switch to control three separate rate settings.
What the signal values mean
Channel values are pulses that typically range from 1000 to 2000 microseconds, with 1500 at the center. Many radio screens show the same range as -100% to +100%.
For a throttle channel, the low end (around 1000 microseconds) is usually idle or off, not the center. Check the setting before you connect a motor.
PWM and serial channels
A PWM receiver has one output pin for each channel. Serial protocols, such as SBUS, CRSF, and iBUS, carry eight or more channels over a single wire. Flight controllers usually use the serial output.
The number of channels you can actually use is the lower of the transmitter’s count and the receiver’s count. A 12-channel radio paired with an 8-channel receiver gives you eight usable channels.
Mixing channels
One channel can drive two servos by way of a Y-harness, such as two aileron servos on one channel. Separate channels also allow mixing. Mixing combines stick inputs to control surfaces in ways that a single servo cannot:
- Flaperons combine ailerons and flaps.
- Elevons combine elevator and aileron on two servos, used on flying wings.
- V-tails combine rudder and elevator on two surfaces.
These setups use the sticks you already have. They do not need extra sticks.
Channels on quadcopters
A quadcopter uses four stick channels for roll, pitch, yaw, and throttle. It also uses auxiliary switches for functions such as arming, flight mode, and a beeper. See how to fly an FPV drone for the first time for how these are used. The idea is the same, but the layout is different.
Common misconceptions
- A channel is a radio frequency. In RC, a channel is a control function. In radio spectrum, the word channel can refer to a frequency slot, but a 2.4 GHz system hops across many frequencies, so there is no single channel frequency to point to.
- Elevons and V-tails need extra sticks. They use two servos mixed from the existing stick inputs.
- Channel numbers are the same on every brand. Numbering and default order vary, so check the manual.
- More channels gives better range or link quality. Channel count does not change range. Protocol and link quality do.
What this means for your setup
Start by counting what the plane needs: the number of functions to control, and whether any need switches. Then check the receiver’s channel count and output type. Finally, check the radio’s channel order before the first flight. For choosing a radio with the right count, see choosing a transmitter and receiver for your RC plane. For the wider system, see the RC plane electronics guide.