Dual rates and expo both shape how a control surface responds to your stick, and they are often confused. Dual rates set how far the surface moves. Expo changes how sensitive the surface feels near center. Set both on the transmitter after the mechanical setup is right.
Dual rates scale the maximum throw. Expo softens the response near center. Expo does not reduce the maximum throw.
What dual rates do
Dual rates (D/R) scale a control’s maximum throw by switch position. A common setup has a low rate of about 60 to 70 percent for takeoff, landing, and early training, and a high rate of 100 percent for full-throw maneuvers. Dual rates usually apply to ailerons, elevator, and rudder, not to throttle.
Many radios offer triple rates on a three-position switch, which gives a low, middle, and high setting. Some radios allow rates above 100 percent, up to about 125 to 150 percent. A rate above 100 percent can push the surface past the throw you set mechanically, so check the throw after you change it.
What expo does
Expo changes the shape of the response curve. With positive expo on many radios, the response is softer near center and reaches full throw at the ends of the stick. Small stick movements then produce small control inputs, which makes the plane easier to fly smoothly.
Expo does not reduce the maximum throw. At full stick, the surface still reaches its full travel.
Sign conventions differ by brand
The sign of the expo value depends on the brand. On Spektrum and EdgeTX radios, a positive value gives a softer center. On Futaba radios, a negative value gives a softer center. Check your radio’s manual, and test the surfaces on the bench before you rely on a value.
Set the throws in the right order
- Set the mechanical throws first. Use the linkage and horn holes to get the maximum throw your manual calls for. See RC plane control rods and pushrods.
- Set the endpoints. Endpoints (travel adjust) set the absolute servo limits, so the surface stops where you want it.
- Set the dual rates. Rates scale the throw within the endpoints.
- Set the expo. Expo shapes the response around center.
Rates cannot fix a poor mechanical setup. A heavy rate reduction also costs servo resolution, because the servo has fewer steps to move the surface.
Use the throws in your manual, in millimeters or degrees, for the low and high settings.
Starting points
These are starting values, not settings that suit every plane.
- Trainers: a low rate of about 60 to 70 percent, and expo of about 20 to 30 percent.
- Sport and aerobatic planes: expo of about 20 to 40 percent.
- 3D planes: high rates are often paired with expo of about 50 to 70 percent.
Start with the manual’s suggestions, fly the plane, and adjust from there.
Switch layout
Use the same position for low rate on every rate switch. For example, set low rate away from you and high rate toward you, on all of your rate switches. Mixed positions are easy to confuse in the middle of a maneuver.
Dual rates and expo can share a switch on some radios. In that case, one switch position can change both values together, or you can set the switch to change only the throw or only the expo. Check how your radio handles this before you rely on it in the air.
Flight modes
On EdgeTX radios, flight modes can switch rates and expo together for each phase of flight, such as takeoff, cruise, and aerobatics. Set the modes up on the ground, and test each one before flying.
Common misconceptions
- Rates and expo are the same thing. They are not. Rates set the maximum throw, and expo shapes the response.
- Expo reduces maximum throw. It does not.
- Positive expo is always softer. It depends on the brand.
- Rates can fix a poor mechanical setup. They cannot, and heavy reduction costs servo resolution.
Safety
- Confirm which switch position is low and which is high before takeoff.
- Test each surface on the ground at every switch position.
- Re-check the throws after any change to the rates, expo, or linkage.
For the mechanical side of setting throws, see RC plane control rods and pushrods. For radio features, see choosing a transmitter and receiver for your RC plane.