Flying Disciplines

RC Aerobatics and 3D Flying: Styles, Disciplines and Planes

A guide to RC aerobatics: the main styles, what 3D flying demands from a plane, how CAP 232 models fit in, and how to choose a first aerobatic airplane.

On this page
  1. What RC aerobatics covers
  2. The main aerobatic styles
  3. What 3D flying asks of a plane
  4. Why the CAP 232 is a common benchmark
  5. Choosing a size
  6. Other flying disciplines
  7. Safety basics for aerobatic flying
  8. Where to start

What RC aerobatics covers

RC aerobatics means flying a radio-controlled airplane through a set of maneuvers such as loops, rolls, spins and knife-edge passes. The name covers several styles. They share the same basic skills, but they differ in how a flight is judged, how the plane is built, and how closely the flight resembles a full-size aerobatic routine.

Picking a style first saves money, because each discipline favors different airframes.

The main aerobatic styles

Precision pattern (F3A)

F3A is the FAI class for precision aerobatics, usually called pattern. The pilot flies a set schedule of maneuvers inside an imaginary box in front of them, and judges score each one. Clean lines, constant speed and accurate geometry count for more than tricks. F3A pattern aerobatics covers the rules and how to start.

Scale aerobatics (IMAC)

Scale aerobatics flies models that look like full-size aerobatic aircraft. The International Miniature Aerobatic Club (IMAC) runs classes from Basic, Sportsman, Intermediate and Advanced up to Unlimited, plus a Freestyle class. Known sequences are published in advance. Unknown sequences are given to pilots shortly before they fly.

Scale classes need replicas of full-size aerobatic types. The CAP 232 is one of the types that fits.

3D and freestyle

3D flying uses hovers, harriers, torque rolls and similar maneuvers that depend heavily on thrust and large control inputs. Common 3D maneuvers include the hover, the torque roll, the harrier, the waterfall, the blender and the knife-edge spin. Freestyle contests are judged on difficulty, presentation and music.

Indoor precision (F3P)

F3P is the FAI indoor class. Pilots fly very light foam planes in sports halls, in a precision class and an aero-music freestyle class. F3P indoor aerobatics explains the weight limit and how these planes are built.

What 3D flying asks of a plane

3D flying depends more on power and control authority than on speed.

  • Thrust: A 3D plane needs more thrust than its weight. Many designs sit between about 1.5:1 and 2:1 thrust-to-weight. A hovering plane is held up by its propeller’s thrust, not by wing lift.
  • Control throws: Full 3D throws are large, roughly 40 to 50 degrees of elevator and rudder and 35 to 45 degrees of aileron. Precision flying uses much smaller throws, roughly 10 to 25 degrees. The right numbers vary by model, so treat these as a starting point.
  • Rates and expo: Many pilots set dual rates and exponential (expo) somewhere around 30 to 70 percent. Expo softens the center of the stick, and the setting is a matter of personal preference.
  • Control surfaces and servos: 3D surfaces are large, often 30 to 50 percent of the chord, and frequently counterbalanced. Larger 3D models usually need high-torque digital servos.
  • Center of gravity: The range is set by each manufacturer. A CG further back makes the plane more agile and less stable.

More throw is not always better. Excessive throw makes precision maneuvers sloppy.

Why the CAP 232 is a common benchmark

The full-size CAP 232 is a French single-seat aerobatic monoplane, built for unlimited aerobatics. It’s a modern design, not a vintage or biplane, and its scale models are a common choice for IMAC and 3D flying.

Models range from small micro kits and mid-size electric ARFs to 1/3-scale gas models with spans of roughly 2.6 to 2.7 m. Bigger models need bigger engines, bigger servos and a bigger budget for repairs. Kits and ARFs change from year to year, so check current availability by brand.

Experienced pilots often suggest building time on a stable trainer or sport plane before flying a scale aerobatic model. The CAP is a demanding design to start with.

Choosing a size

Size sets the budget, the transport and the power. These are approximate ranges, so check each kit’s specification:

Class Approximate span Typical power
Foam 3D 0.8 to 1.3 m Electric
50cc class 2.1 to 2.3 m Gas, about 50cc
33% scale 2.6 to 2.7 m Gas, about 100 to 120cc
40% scale 3.1 m or more Gas, larger

A foam 3D model is not a beginner trainer. Its light weight and quick response make it hard to fly for a pilot who has not yet built the basic skills.

Other flying disciplines

Aerobatics is one part of RC flying. The other disciplines use the same radio gear and many of the same skills, but they’re built around different planes and goals:

For a sense of how hard different planes are to fly, see what makes an RC plane hard to fly.

Safety basics for aerobatic flying

  • Never hover or fly low 3D passes toward yourself, spectators or the pits.
  • Large gas propellers can cause severe injuries. Use a throttle cut or kill switch, and set the failsafe to throttle off.
  • Charge LiPo batteries with care, and store them in a fireproof container.
  • Where you can, fly from a known field with a club or an experienced pilot.

Where to start

Start with a stable, well-known sport plane or trainer, and learn to fly it smoothly before you move to a dedicated aerobatic model. A flight simulator lets you practice maneuvers and failsafe reactions without risking a plane.

Then choose a discipline, ask a club or an experienced pilot to check your setup, and raise your rates and throws slowly as your skills grow.

Keep exploring

Guides from other topics

All topics →