Failsafe is what a receiver’s outputs do when it loses the radio link. Set a failsafe on every plane. Test it on the ground before the first flight, and again after any change to the setup. A failsafe that is set wrong can leave the motor running after the pilot loses contact.
What counts as signal loss
A receiver watches for valid radio frames. When the frames stop, the receiver switches to its failsafe behavior after a short delay, typically about half a second to one second, depending on the system. Some systems show a drop in link quality before the link fails completely, so telemetry alarms can give you warning.
Failsafe modes
- Hold: the outputs keep their last positions. The risk is that a throttle left up stays up, and the plane can fly away.
- Custom (preset): you choose the output position for each channel. A common preset is throttle off with a gentle turn-and-descent setting on the surfaces.
- No pulses: the receiver stops sending a signal. This works only if the ESC cuts power to the motor when the signal stops. Check that behavior on your ESC before you rely on it.
Some radios let you choose a mode for each channel, and some receivers use their own settings. Check which options your system offers.
Set the throttle first
At minimum, throttle should go to idle or off when the link is lost. Many flying clubs require or recommend this, so check your club’s rules.
- Electric planes: the motor should stop. Confirm that your ESC actually stops the motor, not just idles it.
- Glow or gas planes: the engine should idle or cut, depending on how the engine is set up.
Set the control surfaces
A common preset is throttle off, a small amount of up elevator, and a little rudder or aileron. The plane then turns gently and descends, rather than diving. The right preset depends on the plane and the pilot, so choose the one you would want if you lost contact. Keep the surface positions moderate. A large control input can stall the plane at low speed.
Brand notes
Setup differs between systems, so check the manual for your receiver.
- Spektrum: many receivers set failsafe during binding, using the stick and throttle positions you hold then. SmartSafe sets only the throttle channel.
- FrSky and EdgeTX: choose Hold, Custom, No pulses, or the receiver setting in the model’s setup.
- ExpressLRS PWM receivers: many let you set failsafe for each output.
GPS flight controllers and return-to-home
Flight controllers running INAV or ArduPilot, as on many FPV planes, can return the plane home or land it on failsafe. Only GPS-equipped systems like these can do that. A plain receiver failsafe does not bring a plane home. Check your autopilot’s documentation for the failsafe options in your firmware version.
Some autopilots include more drastic failsafe options. Learn what each one does, and whether it is permitted where you fly, before you enable it.
Testing failsafe on the ground
Run this test before the first flight of any new setup, and after any change.
- Secure the plane so it cannot move, and remove the prop.
- Power on the transmitter, then the receiver.
- Apply some throttle, and move each control so you can see its position.
- Turn the transmitter off.
- Check each output. The throttle should go to its failsafe setting, and each surface should move to its preset.
- For an electric plane, confirm the motor stops, or does what you set it to do.
- Turn the transmitter back on and confirm normal control returns.
Do not test failsafe by switching off the transmitter during a flight. The test belongs on the ground, with the plane restrained.
Retest after changes
Retest the failsafe after rebinding, after a receiver swap, and after a firmware update. These changes can reset the failsafe settings.
Common misconceptions
- Factory defaults are safe. Some receivers default to Hold, which can keep the throttle where it was. Check the setting.
- Any failsafe brings the plane home. Only GPS-equipped flight controllers can do that.
- Failsafe is permanent. Rebinding can reset it.
- Switching off the transmitter in flight is a valid test. It is not a safe way to test, so do the test on the ground.
Checklist
- Throttle goes to idle or off on signal loss.
- Surface preset is set and moderate.
- No-pulses mode is used only after you have confirmed your ESC cuts power.
- The ground test is done with the plane restrained.
- The test is repeated after binding, receiver changes, and firmware updates.
For binding the receiver first, see how to bind a transmitter and receiver. For the range check and radio features, see choosing a transmitter and receiver for your RC plane.