Control rods, also called pushrods, carry motion from the servo to the control surface. A good linkage is straight, free of play, and centered. This guide covers the common rod types and how to set one up.
The linkage chain
A typical linkage runs from the servo to the surface like this: servo, servo arm, pushrod, clevis, control horn, and control surface. Every joint can add play. Every bend can add friction. Geometry changes how far the surface moves and how hard the servo has to work.
Rod types
- Wire pushrods are steel music wire in a tube. They are the most common choice on sport and trainer planes.
- Carbon rods with threaded ends are stiff and light. They suit larger or faster models.
- Wood dowels with wire ends are used on large models.
- Pull-pull cables use two cables under tension. They are common for rudders and sometimes elevators.
Choosing wire size and thread
Wire size depends on the model and the loads on it. As a rough guide, micro and park flyers often use wire around 0.8 to 1.2 mm. Sport planes in the .40 to .60 size class often use wire around 1.5 to 2 mm, or a 2-56 thread. Giant scale models often use a 4-40 thread. Check your plane’s manual, since the kit maker’s specifications come first.
Clevises, keepers, and retaining collars
A clevis connects the pushrod to the control horn. Metal clevises are strong and suit most sport planes. Nylon clevises work on light park flyers, but they can flex or open on larger, faster planes.
Secure every clevis. Metal clevises should use a retaining collar, such as a short piece of fuel tubing or silicone, or a locknut. Screws on EZ-connectors can vibrate loose, so use a drop of thread-locker on them as well.
Z-bends, L-bends, and EZ-connectors
- Z-bend at the servo end is secure, but changing it means removing the servo horn.
- L-bend with a keeper lets you adjust the length at the horn end and is easier to change.
- EZ-connectors are adjustable connectors that clamp onto the rod. Check their screws after the first few flights.
Servo arm and horn geometry
At neutral, the servo arm and the control horn should be parallel, and the pushrod should sit at about 90 degrees to both. The hole in the control horn should line up with the hinge line. A horn that sits off that line can produce uneven throws. For fitting the servo itself, see how to mount servos in an RC plane wing.
Keep pushrods as straight as you can. Each bend adds slop and binding.
Setting neutral
- Center the servo electronically. Set the transmitter’s trim and subtrim close to zero with the servo at its neutral point.
- Attach the servo arm and the rod with the control surface centered.
- Adjust the rod length mechanically, not with large subtrim.
Large subtrim can hide a badly adjusted rod, but it makes the throws uneven, with more travel in one direction than the other.
Throws and mechanical advantage
Throw is how far a control surface moves. Moving the clevis to a different hole on the servo arm or horn changes the throw:
- A longer control horn or a shorter servo arm gives more torque and less throw.
- A shorter control horn or a longer servo arm gives more throw and less torque.
Set the throws mechanically first, so that the surface moves the amount your manual specifies. Then fine-tune with the radio’s endpoints and dual rates. For that step, see dual rates and expo on RC transmitters.
Eliminating slop and binding
- Slop: with the servo centered, the surface should not move when you push it gently. Play in a clevis, a ball link, or the servo gears shows up as movement here.
- Binding: move the surface through its full travel by hand. It should move freely, and the servo should not strain.
Support long pushrods every 6 to 8 inches (15 to 20 cm) with guides, so they cannot flex. Ball links reduce slop and are common on 3D and larger planes.
Slop and flexible linkages can cause flutter, which can damage a control surface in flight. Remove play on faster models. Binding overloads the servo and drains the battery faster.
Pull-pull systems
A pull-pull system uses two cables that run around pulleys and hold each other in tension. Set the tension with crimp tubes and turnbuckles. The cables should be taut but should not bind. Check tension again after the first flights, because cables can settle.
Checking the linkage on the bench
- Move each surface by hand. Confirm there is no free play at neutral.
- Move the servo through its full range with the linkage connected. Confirm there is no binding.
- Check that each surface moves in the right direction for its stick.
- Measure throws against the manual, in millimeters or degrees.
Common mistakes
- Using large subtrim to fix a badly adjusted rod.
- Using nylon clevises on large, fast planes.
- Setting linkages too tight, which causes binding.
- Skipping thread-locker on EZ-connector screws.
- Adjusting endpoints before the mechanical setup is correct.
Safety
Flutter from slop or flexible linkages can destroy a control surface in flight. Check every linkage before each flight, and test again after any change.