Electronics

RC Plane Retracts: Choosing and Installing Retractable Landing Gear

How to choose and install RC plane retracts: compare electric, pneumatic, and mechanical types, plan mounts and power, and troubleshoot gear that won't cycle.

On this page
  1. Types of retracts
  2. Choosing retracts for your plane
  3. Mount types and struts
  4. Mounting and wheel-well clearance
  5. Wiring and power
  6. Doors and sequencing
  7. Pneumatic systems
  8. Ground testing before flight
  9. When retracts misbehave
  10. Common mistakes
  11. Safety

Retractable landing gear folds the wheels into the wing or fuselage in flight, which reduces drag. The benefit is real on smooth fields, but retracts add weight, cost, and parts that can fail. This guide covers the main types, how to mount and power them, and what to do when they misbehave.

Types of retracts

  • Electric retracts have a motor in each unit. They plug into a receiver channel, often through a retract controller or a Y-harness. They are the most common choice on foam planes and mid-size models.
  • Pneumatic retracts use compressed air from an onboard tank, controlled by a servo-operated valve. They are used on large scale and giant warbird models. They need tubing, a tank, and regular leak checks.
  • Mechanical retracts are driven by a single servo through pushrods and linkages. They are light and affordable, but they put heavy loads on the servo’s gears.

Choosing retracts for your plane

Start with the plane’s weight and size. Each retract is rated for a range of weights, and the manufacturer’s rating is the number to follow. Retracts add roughly 50 to 200 grams per set on sport models, depending on size. That weight counts against the plane’s performance, as the wing loading guide explains.

Consider the landing surface, too. Retracts are fragile on grass and rough strips. A plane that flies mostly from grass may do better with fixed gear.

Mount types and struts

Mounts come in a few common arrangements:

  • 90-degree mounts are the most common.
  • 85-degree or rotating mounts are used on warbird-style planes, where the wheel rotates as it folds.
  • Straight trunnion mounts suit some scale and specialty layouts.

Struts can be rigid or oleo. Oleo struts are sprung or air-dampened and absorb landing shock better. On foam models, struts are often 3 to 5 mm wire.

Mounting and wheel-well clearance

Mount the retract to hardwood or plywood rails, not to foam. Retract plates are often 3 to 6 mm aircraft plywood. Foam will not hold the loads.

Plan the wheel well so the wheel and strut have clearance all around. Check full travel with the plane on a stand before you close the doors. A wheel that touches the wing or fuselage while it moves can jam the gear or damage the structure.

Wiring and power

  • Switch channel: use a dedicated switch channel, often the gear channel. Some controllers offer adjustable speed for sequenced doors.
  • Power draw: electric retracts can draw roughly 0.5 to 2 amps or more while moving. Check that the receiver’s power supply, usually the ESC’s BEC or a separate battery, can handle that load alongside the servos.
  • Stall cutouts: many electric units have a stall or overcurrent cutout. Repeated stalls can burn out the motor, so do not keep cycling a gear that won’t move.
  • Failsafe: decide whether the gear should stay in its current position or go down if the signal drops. Set it on purpose.

For how power is shared in the plane, see the RC plane electronics guide.

Doors and sequencing

Many retract systems use doors. The door has to open before the gear moves, and it has to close after the gear is locked. A sequencer handles this order. A typical cycle is: doors open, gear moves, doors close. Set the sequencer’s delays and check each step on the stand.

Mechanical retracts need a servo suited to the job. Many are non-proportional, 180-degree servos, not ordinary proportional servos.

Pneumatic systems

Pneumatic retracts are typically charged to about 80 to 120 psi, but check the manufacturer’s rating. Use only the pressure the manufacturer specifies. Higher pressure does not fix a stiff gear. It can cause harm.

Check O-rings, tubing, and fittings before each session. Pneumatic systems are not leak-free by default. A slow leak can make the gear slower each cycle.

Ground testing before flight

  1. Support the plane on a stand that cannot tip.
  2. Remove the prop or disable the engine.
  3. Keep fingers clear of wheel wells and doors. Mechanisms can pinch hard.
  4. Cycle the gear several times, and watch the full travel and the doors.
  5. Check the receiver and power supply under load. Watch for resets.
  6. Confirm the gear locks fully up and fully down, without stalling.

Also think about speed. Do not cycle the gear at any speed. Lower it at a slower speed, because airflow loads at high speed can stop it from extending and can damage the mechanism.

When retracts misbehave

If a retract stops working, avoid swapping the unit first. A bent strut, a tight wheel well, a weak power supply, a damaged lead, or a wrong endpoint can cause the same symptoms. Work through the causes in this order:

  1. Support and disable the plane. Use a stand that cannot tip, and disable the power system.
  2. Inspect the damage path. Check the struts, mounts, rails, doors, and surrounding structure for a shift from a hard landing.
  3. Remove outside loads. Disconnect a gear door or take off a wheel if it rubs. See whether the unit moves freely without the load.
  4. Check power under load. A meter reading with nothing moving is not enough. Watch the voltage while the gear cycles, and avoid stalls.
  5. Check the radio and controller. Confirm the channel, switch, direction, travel, and delay settings. A copied model memory can carry unexpected settings.
  6. For pneumatics, find the leak. Pressurize only to the specified range, and isolate sections of tubing and fittings to find where the pressure drops.
  7. Change one thing at a time. Make one correction, repeat the same test, and compare the results.

Use this table to narrow down the cause:

What you see Where to look
The gear works on the bench but not in the wing Binding from the installation, the strut, a wheel, or a door
All units fail at once Shared power, the controller, the switch, the channel, or the air supply
The receiver resets during a cycle The gear load is pulling down the voltage
The gear moves one way but not the other Mechanical load in that direction, endpoints, or limit switches
A pneumatic gear slows over time A leak or an undersized supply

Do not keep cycling a jammed electric retract, and do not raise the travel past the mechanism’s limit to force a lock. Both can burn out the motor or damage the mechanism.

Common mistakes

  • Cycling a jammed retract until the motor burns out.
  • Pushing travel beyond the mechanism’s limit.
  • Flying with a voltage drop that resets the receiver.
  • Using more air pressure to overcome friction.
  • Adjusting the sequencer before checking that the doors move freely.

Safety

Keep fingers clear of wheel wells when you cycle the gear. Mechanisms can pinch. Support the plane securely before you test, and disable the power system. For broader guidance, see choosing a transmitter and receiver for your RC plane and failsafe setup for RC planes.

The complete guide to electronics

RC Plane Electronics: A Complete Guide to Every Component
Read the guide

Keep exploring

Guides from other topics

All topics →