Electronics

Choosing a Transmitter and Receiver for Your RC Plane

Choose an RC plane transmitter and receiver by channel count, protocol, radio features, and receiver type, with a checklist to use before you buy.

On this page
  1. How many channels do you need
  2. Protocols: the detail that decides compatibility
  3. Basic radios and computer radios
  4. Stick modes and gimbals
  5. Receivers
  6. Range and range class
  7. Is it legal to fly RC airplanes?
  8. Checklist before you buy
  9. Range check and failsafe before the first flight

A transmitter and receiver form the radio link that turns your stick movements into control surface movement. When you choose a pair, three things matter most: how many channels you need, which protocol the two units share, and which features you will actually use. Brand matters less than these.

How many channels do you need

  • 3 channels: rudder, elevator, and throttle. This is enough for a classic trainer without ailerons.
  • 4 channels: adds ailerons. Most sport planes and trainers with ailerons need this.
  • 6 or more channels: adds flaps, retracts, rate switches, gyro gain, lights, and similar switch functions.

It is reasonable to buy a radio with a few spare channels, but there is no need to pay for channels you will never use. For what a channel is, see what channels are in RC.

Protocols: the detail that decides compatibility

The transmitter and receiver must share a protocol. Common protocols include:

  • Spektrum DSM2 and DSMX
  • FrSky ACCST and ACCESS
  • Futaba FASST, FASSTest, and T-FHSS
  • FlySky AFHDS 2A and AFHDS 3
  • ExpressLRS (ELRS) and TBS Crossfire

Two radios can both use 2.4 GHz and still not link. For details, see can you use any RC transmitter with any receiver.

Some radios have a module bay, so you can add a module to support a different protocol. Multi-protocol modules cover many protocols but not all of them, so check the module’s list before you buy.

Basic radios and computer radios

A basic radio has a small number of settings and usually stores only a few models. It can be enough for a single trainer.

A computer radio stores many model memories, often from 20 to more than 250. It also mixes channels, adjusts rates and expo, sets failsafes, and runs timers. Computer radios run one of two firmware families. EdgeTX is common on many radios from Radiomaster and Jumper, along with some FrSky radios. Spektrum, Futaba, and JR radios use their own firmware.

Ready-to-fly (RTF) packages often include a basic transmitter. Check whether it has model memory and mixing, because many do not. If you plan to fly several planes or tune rates and expo, a computer radio will likely serve you better. For how those settings work, see dual rates and expo on RC transmitters.

Stick modes and gimbals

The stick mode sets which stick controls throttle. Mode 2, with throttle on the left stick, is standard in the United States and most other countries. Mode 1, with throttle on the right stick, is more common in parts of Europe and Japan. Many radios can switch between the two, but check the manual before you change anything.

Gimbals are the stick assemblies. Potentiometer gimbals use a wiper that moves across a track, and the wiper wears over time. Hall-effect gimbals use magnets and sensors, so there is no wiper to wear. Hall-effect gimbals are worth looking for on a radio you plan to keep for years.

Receivers

Receivers differ in how they send data out:

  • PWM receivers have one output pin per channel. They suit simple planes with a few servos.
  • Serial receivers send many channels down one wire, using protocols such as SBUS, iBUS, CRSF, or SRXL2. Flight controllers usually need a serial output.

Some receivers support telemetry, which sends voltage and signal data back to the radio so you can set alarms. Receivers with two antennas are called diversity receivers. Mount the antenna tips at 90 degrees to each other, away from carbon fiber and metal parts.

Range and range class

Full-range 2.4 GHz receivers often list a range of 1 km or more in line of sight. Park-flyer receivers have shorter range. Range depends on the system, the antenna, and the surroundings, so treat any listed figure as the manufacturer’s claim. Do a range check before flying (see below).

Rules depend on where you live and where you fly. Depending on your country, rules may cover which radio bands you can use, transmit power, registration of some aircraft, and where you can fly near people, buildings, or airports. Check with your national aviation authority and any local rules that apply to your field. Many flying clubs have a site and may include liability insurance with membership, so ask what yours covers. This article does not give legal advice, and rules change.

Checklist before you buy

  1. Count the functions you need, and add a few spare channels if you like.
  2. Pick a protocol family, and confirm the receiver or module uses it.
  3. Decide whether you need model memory and mixing. Most pilots with more than one plane do.
  4. Choose the receiver type: PWM or serial, with or without telemetry, and single or diversity antenna.
  5. Confirm the range class suits the field where you fly.
  6. If you plan to upgrade later, check the firmware and whether the radio has a module bay.

Range check and failsafe before the first flight

Before the first flight of any new setup, do a range check in the radio’s reduced-power mode. Some manufacturers suggest about 30 paces, but the right distance varies by system, so follow your manual. Then set and test the failsafe. See failsafe setup for RC planes and how to bind a transmitter and receiver.

For the rest of the system, start with the RC plane electronics guide.

The complete guide to electronics

RC Plane Electronics: A Complete Guide to Every Component
Read the guide

Keep exploring

Guides from other topics

All topics →