Building

RC Glider and Flying Wing Plans: Where to Find Them and How to Build

Where to find free and paid RC glider and flying wing plans, how to check print scale, glider types, flying-wing essentials and build options.

On this page
  1. Where to find free plans
  2. Paid plans and magazine reprints
  3. Check the print before you cut
  4. Glider types
  5. Launch methods
  6. Classic designs
  7. Flying wings: what changes
  8. Glider airfoils
  9. Build options
  10. Keep it straight
  11. Common mistakes
  12. Safety

Where to find free plans

Several free plan sources are widely used:

  • Plan archives such as Outerzone and AeroFred, which hold many vintage designs
  • RCGroups build threads and plan downloads
  • Flite Test free foam-board designs, including flying wings

Free plans are useful, but they are not always correct. Vintage scans can be distorted or missing details. Check the plan against a dimension you can measure before you trust it.

Plan lineups change, so check each source before you start a project.

Paid options include the AMA Plans Service, magazine plan reprints, and plan publishers such as Traplet. Plan availability changes over time, so confirm a plan is still offered before you order it.

Check the print before you cut

A printed plan is only useful at the right size. Compare the printed scale against the plan’s scale bar or a known dimension. Tiled PDFs must print at 100%, not “fit to page,” or the parts will be the wrong size.

Glider types

  • Thermal gliders climb in rising air and are often flown with rudder, elevator and spoilers.
  • Slope gliders soar in ridge lift and are usually flown with ailerons.
  • Discus-launch (DLG) gliders are launched by throwing them like a discus.
  • Electric gliders (F5J style) carry a motor for the climb, so they don’t need a launch line.

Launch methods

Gliders can be launched by hand toss, hi-start (a bungee and line), winch, discus throw, or from slope lift. Some models use a motor to climb first.

Hi-start and winch lines are under tension. Keep clear of the line, and stake the launch equipment firmly.

Classic designs

Several classic designs show up in plan collections, including the Gentle Lady, Olympic II, Bird of Time, Spirit and Sagitta, and the Zagi flying wing. Confirm a plan is still available from a current source before you start.

Flying wings: what changes

A flying wing has no separate tailplane, so the wing itself has to be stable and controllable. Three things make that work:

  • A reflexed airfoil, with the trailing edge turned slightly up, gives pitch stability. The airfoil guide explains the reflexed sections used on flying wings.
  • Sweep and washout. Washout means the wingtips are set at a lower angle than the root. Designs often use a few degrees at the tips, but the amount varies.
  • Elevons, which combine the aileron and elevator functions. Set modest throws for the first flight.

The balance point is usually far forward, often around 15 to 25% of the mean aerodynamic chord. Follow the plan’s figure exactly. A flying wing that is tail-heavy cannot be controlled. The center of gravity guide explains how to find the balance point.

Glider airfoils

Common glider sections are thin and cambered, about 7 to 10% thick, such as SD7037, RG15 and the AG series. These suit the low Reynolds numbers gliders fly at, where many full-scale airfoils perform poorly.

Build options

  • Built-up balsa: ribs, spars and sheeting. This is the traditional route.
  • Hot-wire foam cores sheeted with balsa, for a light, strong wing.
  • EPP slope wings, which are tough and resist dings.
  • Foam board for a simple first build.

Keep it straight

Gliders show warps more than powered planes do. Build straight and true. Check each panel for twist with a straightedge before you cover it, because a warp locked in under the covering is hard to fix.

Common mistakes

  • “Gliders are easy beginner builds.” Large, light structures need careful, warp-free building.
  • “Any airfoil works on a flying wing.” Without reflex or washout, a flying wing has no pitch stability.
  • “Free plans are always correct.” Check them against a measurement before you cut.

Safety

  • Keep clear of hi-start and winch lines when they are under tension.
  • Stake the launch equipment firmly before every launch.

The complete guide to building

Building RC Planes: Balsa Kits, Materials and Techniques
Read the guide

Keep exploring

Guides from other topics

All topics →