An electric RC plane is a set of small parts that have to work together. This guide covers what each part does, how they connect, and the safety habits that matter most. Each section links to a spoke article that goes deeper on one topic.
How the parts connect
An electric RC plane is really two systems that share a battery:
- Signal chain: the transmitter (the radio you hold) sends stick and switch positions over a radio link to the receiver in the plane. The receiver passes each channel out to the servos and the speed controller.
- Power chain: the flight battery feeds the electronic speed controller (ESC), which drives the brushless motor. The ESC usually also powers the receiver, and the receiver powers the servos.
In order, the usual route looks like this:
- Battery to ESC (main power in)
- ESC to motor (three wires on a brushless motor)
- Receiver to ESC (throttle signal on one channel; the same lead can carry power back to the receiver)
- Receiver to servos (one servo per control surface)
- Transmitter to receiver (the radio link, set up by binding)
Transmitter and receiver
The transmitter is the radio you hold. It reads your sticks, knobs, and switches and turns them into channel values. Most modern radios use the 2.4 GHz band, where the signal hops across many frequencies. Some long-range systems, such as ExpressLRS 900 and TBS Crossfire, use the 868 or 915 MHz bands where they are legal. Which bands you can use depends on your country.
The receiver sits in the plane and turns the radio signal back into channel outputs. The transmitter and receiver must share a protocol to link. Matching the band is not enough. See can you use any RC transmitter with any receiver for why this matters.
A basic trainer needs at least three channels: rudder, elevator, and throttle. Adding ailerons brings the count to four, and flaps, retracts, and lights add more. For help with channel counts, see what channels are in RC. For help choosing a radio, see choosing a transmitter and receiver for your RC plane.
Servos
Servos move the control surfaces: ailerons, elevator, rudder, and often flaps. The receiver sends each servo a pulse about 50 times per second (50 Hz). The width of the pulse sets the position. A pulse of about 1000 microseconds moves the servo to one end of its travel, 1500 microseconds puts it at center, and 2000 microseconds moves it to the other end. Digital servos can accept faster update rates than older analog servos.
Servos come in rough size classes. Micro servos weigh about 5 to 9 grams, mini servos about 20 grams, and standard servos about 40 to 45 grams. Torque is listed in kg·cm at a stated voltage, so compare servos at the same voltage.
A standard servo lead has three wires: signal (white, yellow, or orange), positive (red, in the middle), and ground (black or brown). Colors vary by brand, so check the plug before you connect it.
Servos connect to the control surfaces through pushrods and horns. See control rods and pushrods for setup, and how to mount servos in an RC plane wing for installing them.
ESC, BEC, and motor
The ESC takes the throttle signal and switches power to the motor. A brushless motor has three wires, and the ESC sends power through them in sequence. Swapping any two of the three wires reverses the motor’s direction.
Choose an ESC rated for a continuous current above the motor’s maximum draw, with about 20 to 30 percent headroom. Measure the current at full throttle rather than relying on the motor’s listed figure. For motor and propeller pairing, see RC plane motor and propeller selection.
Most ESCs include a BEC (battery elimination circuit). It steps the pack voltage down to roughly 5 to 6 volts for the receiver and servos. Linear BECs suit small planes with few servos at low cell counts. Switching BECs (often called SBECs or UBECs) handle more servos and higher voltages. Some ESCs have no BEC at all. These are called opto ESCs, and they need a separate supply for the receiver.
Batteries and connectors
Most electric planes use lithium polymer (LiPo) packs. Each cell is 3.7 volts nominal and 4.20 volts when fully charged. Common pack sizes are 2S (7.4 volts), 3S (11.1 volts), 4S (14.8 volts), and 6S (22.2 volts). The “S” number is the count of cells in series.
Capacity, in mAh, affects flight time and weight. The C rating shows how quickly the pack can deliver current. As a rough guide, the maximum discharge in amps is the C rating times the capacity in amp-hours. Listed C ratings are often optimistic, so treat them as an upper bound. For charging and storage, see LiPo batteries for RC planes.
Common connectors include XT60 and XT90 for main power, EC3 and EC5, and Deans (T-plug). Balance leads use a JST-XH plug for charging. A connector’s rating is often higher than the wire it is crimped to can carry, so size the wire for the current, not the plug.
Powering the receiver
A receiver should get its power from one source at a time. There are three common setups:
- ESC BEC: the ESC’s BEC powers the receiver through the throttle lead. This is the usual setup.
- Separate battery or BEC: if you power the receiver directly, unplug the red wire from the ESC lead so the ESC does not also feed the receiver.
- Twin-engine planes: with two ESCs, disable the red wire on one of them so the receiver is not fed twice.
Feeding one receiver from two sources can damage electronics. Check the wiring before the first power-up.
Stabilizers, flight controllers, and telemetry
Some receivers include built-in gyro stabilization, such as Spektrum AS3X or SAFE. A flight controller, such as one running ArduPilot or INAV (common on FPV planes), adds autopilot features such as GPS return-to-home. A flight controller sits between the receiver and the servos and ESC.
Telemetry on most current radio systems sends data back to the transmitter, such as pack voltage and link quality. Alarms can warn you about a low battery or a weak signal. These features depend on the system, so check what your radio and receiver support.
Lights and add-ons
LED lights for an RC plane can run from the receiver’s BEC or from the main pack through an LED controller. Strips rated for 12 volts suit a 3S pack. Check the current draw first. Lights can draw roughly 50 to 500 mA, depending on the lights, so make sure your BEC has capacity for them alongside the servos.
Navigation lights follow a common convention: red on the left wingtip, green on the right wingtip, and white at the tail.
Retracts are another common add-on. They draw a lot of current while they move. See RC plane retracts before you add them.
Common misconceptions
- Higher Kv means more power. Kv is motor RPM per volt. Power is volts times amps.
- More mAh means more speed. A bigger pack adds flight time, but it also adds weight.
- More channels means a better radio. Link quality and protocol matter more than channel count.
- All 2.4 GHz gear works together. Protocols differ between brands, and sometimes within a brand.
Safety checklist
- Remove the propeller for bench setup and binding.
- Turn the transmitter on before you connect the flight pack. Disconnect the pack before you turn the transmitter off.
- Charge LiPo packs only while you are watching them, in a LiPo bag or a fire-safe container.
- Range-check the radio and test the failsafe on the ground before the first flight. See failsafe setup for RC planes.