Electronics

How to Bind a Transmitter and Receiver on Your RC Plane

How to bind an RC plane transmitter and receiver: select the right model memory, bind in the correct order, confirm the link, and check failsafe.

On this page
  1. What binding does
  2. Before you start
  3. General steps
  4. Brand examples
  5. After binding
  6. Binding problems
  7. When you change radios
  8. Safety

To bind a transmitter and receiver, put the receiver into bind mode, put the transmitter into bind mode, and wait until the receiver’s light shows the link is made. Then check the failsafe and test the controls. Binding pairs the receiver with one transmitter, so the receiver knows which signal to accept. You do it once for each receiver and model. The exact steps vary by brand, so follow your manual.

What binding does

Binding stores the transmitter’s identity in the receiver. On some radios, binding also ties the receiver to one model memory, so you need to select the right model before you bind.

Binding does not set throws, channel order, or failsafe. You set those separately. Some receivers do set a failsafe when they bind, so check it afterward.

Before you start

  • Select the model memory first. On many radios, the receiver locks to the model you have open. Make sure the right model is selected or create a new one.
  • Remove the prop or disconnect the motor. The ESC can arm during binding.
  • Keep the transmitter and plane close. Keep them about a meter apart, roughly three feet. Being too close can overload the receiver. Some manufacturers give different distances, so check your manual.
  • Power the transmitter before the receiver. Turn the transmitter on first, then power the receiver.

General steps

  1. Make sure the transmitter is off.
  2. Put the receiver into bind mode. This usually means holding the bind button while you apply power, or inserting a bind plug into the BIND port before you apply power.
  3. Power on the receiver. Its light should flash, which means it is waiting for a transmitter.
  4. Put the transmitter into bind mode. Use the bind menu or bind switch, following your radio’s steps.
  5. Wait a few seconds. The receiver’s light should turn solid, and the radio may beep or show a confirmation.
  6. Turn everything off, and remove any bind plug.
  7. Power on the transmitter first, then the receiver. Check that the light stays solid.

Leaving a bind plug in place can cause re-binding problems and odd behavior, so remove it once binding is done.

Brand examples

These are general outlines. Check your manual for the exact sequence on your model.

  • Spektrum: use the bind plug or button, then power the receiver. Its light flashes. Start bind from the transmitter’s bind menu or bind switch. The light turns solid when linked. Many Spektrum receivers set failsafe during bind, so keep the throttle low during this step.
  • FrSky ACCST: hold the receiver’s F/S button while you power it on, start Bind on the radio, and power-cycle after binding.
  • FrSky ACCESS: register the receiver with the radio first, then bind.
  • FlySky: use the bind plug or button at power-up, then start Bind from the radio’s menu.
  • Futaba: turn on the transmitter, then the receiver, and hold the receiver’s link or mode button for about two seconds.
  • ExpressLRS: use the matching binding phrase in the firmware, or put the receiver into bind mode by power-cycling it three times. Major firmware versions must match.

After binding

  • Remove the bind plug if you used one.
  • Check each control’s direction against its stick, and reverse any that are backward.
  • Set the failsafe, and test it on the ground. See failsafe setup for RC planes.
  • Do a range check in the radio’s reduced-power mode before the first flight.

Binding problems

  • The receiver keeps flashing. It has not linked. Confirm both units are in bind mode, move them about a meter apart, and check that the protocols match.
  • The radio says it is bound, but the controls are wrong. Check that you bound to the right model memory, and check the channel order.
  • Binding fails with a different brand. Binding cannot fix a protocol mismatch. See can you use any RC transmitter with any receiver.
  • Re-binding over and over does not help. Repeated binding does not fix a wrong protocol or a faulty receiver. Stop and check the protocol and the wiring.

When you change radios

A receiver is bound to one transmitter, so when you switch radios, bind the receiver again. Binding can also reset the failsafe, so test it again after the new bind. The same applies after a receiver swap or a firmware update.

Safety

  • Keep the prop off during binding.
  • Turn the transmitter on before the flight pack, and turn it off after the pack is disconnected.
  • Test the controls and failsafe before the first flight. For choosing gear, see choosing a transmitter and receiver for your RC plane.

The complete guide to electronics

RC Plane Electronics: A Complete Guide to Every Component
Read the guide

Keep exploring

Guides from other topics

All topics →