Electronics

RC Plane Motor and Propeller Selection Explained

How to choose an RC plane motor and propeller: start from weight and purpose, read motor numbers and Kv, size props by diameter and pitch, and match the ESC.

On this page
  1. Start with the plane’s weight and purpose
  2. Reading motor numbers
  3. Kv explained
  4. Choosing the battery cell count
  5. Reading propeller size
  6. Two blades or three?
  7. Prop types
  8. Matching the ESC
  9. Measure before you fly
  10. Common misconceptions
  11. Safety

The motor, ESC, battery, and propeller work as one system, and changing one changes the others. This guide explains how to choose each part for a fixed-wing plane and how to check the result before you fly.

Start with the plane’s weight and purpose

How much power a plane needs depends on its all-up weight and what you want it to do. A trainer, a sport plane, and a 3D plane need very different power.

Rule-of-thumb watts-per-pound figures vary a lot between sources. Roughly, you may see 50 to 80 watts per pound for trainers and gliders, 80 to 120 for sport planes, 120 to 150 for aerobatic planes, and 150 to 200 or more for 3D flying. Some guides use higher figures, around 100 for trainers and 125 for sport planes. Treat any single number as a starting point. The motor maker’s propeller chart lists watts and thrust for specific props and voltages, and it is a better source.

Thrust-to-weight is another useful check. Trainers often sit around 0.6 to 0.8 to 1. Sport planes are often near 1 to 1. A 3D plane needs more thrust than its own weight for strong vertical performance.

Reading motor numbers

A number such as 2212 or 3536 usually gives the stator or the can’s diameter and height in millimeters. Brands do not agree on which measurement they use. Some report the stator size, and others report the outer dimensions. A “2826” from one brand can be a noticeably larger motor than a “2826” from another.

Compare the spec sheet’s dimensions with the model’s motor mount. Some brands use their own bolt spacing, so a motor may not line up with the firewall without drilling new holes.

Kv explained

Kv is a motor’s unloaded RPM per volt. A 1000 Kv motor on 10 volts spins at about 10,000 RPM with no load. A propeller adds load and pulls RPM down. Under load, RPM is typically around 80 to 90 percent of the unloaded figure.

Kv is a speed constant, not a power rating. In general:

  • Low Kv (roughly 400 to 900) suits large props on higher voltage, with more torque and slower flight. It is common for 3D and scale planes.
  • High Kv (roughly 1500 to 3000 and up) suits small props, faster planes, and ducted fans.
  • Mid-range Kv is often a good match for general sport flying.

Choosing the battery cell count

Voltage multiplies RPM, so the cell count and Kv have to work together. A higher cell count can deliver the same power at lower current, which can run cooler in the wires and ESC. The motor and ESC, including its BEC, must be rated for the higher voltage. For pack details, see LiPo batteries for RC planes.

Reading propeller size

Props are labeled diameter by pitch in inches, such as 10x4.7. The diameter is the length from tip to tip. The pitch is how far the prop would move forward in one full turn if it were cutting through a solid. Real forward distance is always less because of slip.

A rough theoretical speed follows from RPM and pitch:

Pitch speed (mph) ≈ RPM × pitch (inches) ÷ 1056

For example, a prop with 4.7-inch pitch at 8,000 RPM has a theoretical pitch speed of about 36 mph. Real airspeed will be lower.

Diameter and pitch affect the setup in different ways:

  • More diameter gives more static thrust and better low-speed efficiency, but it loads the motor more heavily.
  • More pitch gives a higher top speed, but it draws more current.

Current rises steeply as prop size grows, so measure rather than guess.

Two blades or three?

Neither is better in every case. Two-blade props are common on sport and trainer planes. Three-blade props are often chosen where more thrust or a smaller diameter is needed, and they can add drag and load on the motor. More blades do not automatically mean more power. The best choice depends on the motor, the prop diameter, and the flying you do. Check the motor maker’s chart for props that suit the motor, and then test whether the result feels right.

Prop types

  • Standard props are the usual choice for most planes.
  • Electric (E) props are thinner and are made for electric motors. Do not use them on glow engines.
  • Pusher props are marked with a P and are made for motors mounted at the rear. Check the marking before you mount one.
  • Folding props reduce drag on a glider when the motor is off.

Balance every prop before use. An unbalanced prop can cause vibration that loosens parts over time.

Matching the ESC

Pick an ESC rated for continuous current above the motor’s maximum draw, with about 20 to 30 percent headroom. For example, a motor with a 50-amp maximum would call for an ESC rated for at least about 60 amps. The ESC’s BEC also needs to power the servos. An opto ESC has no BEC and needs a separate supply for the receiver. For how the BEC fits into the system, see the RC plane electronics guide.

Measure before you fly

  • Use a wattmeter to measure voltage and current at full throttle.
  • Compare the readings with the motor and ESC ratings, and stay under the continuous ratings.
  • Check motor temperature after a flight. A warm motor is normal. A motor that is too hot to hold is a warning sign that the prop, motor, or battery combination is too much for the setup.
  • Treat maximum watt ratings with caution. Many are optimistic burst figures rather than continuous ratings.

Common misconceptions

  • Higher Kv means more power. Kv is a speed constant. Power comes from voltage and current together.
  • Maximum watt ratings are continuous. Many are short-term figures.
  • A bigger prop is always better. An oversized prop can overload the motor and ESC.
  • Pitch equals the distance you travel. Slip reduces the real distance.

Safety

  • Restrain the plane for bench tests, and remove the prop when you are not testing.
  • Never stand in line with the propeller’s arc.
  • Inspect props for cracks, chips, and bent blades, and replace any damaged prop.
  • Check the prop direction and mounting before you connect the battery.
  • Keep the battery disconnected while you set up and mount the prop.

The complete guide to electronics

RC Plane Electronics: A Complete Guide to Every Component
Read the guide

Keep exploring

Guides from other topics

All topics →