Electronics

LiPo Batteries for RC Planes: Charging, Storage and Safety

How to charge and store LiPo batteries for RC planes safely, covering balance charging, storage voltage, discharge limits, damage signs, and disposal.

On this page
  1. How LiPo cells and packs are rated
  2. Choosing a balance charger
  3. Charging step by step
  4. Charging rules to keep
  5. Storage charge
  6. Flying and discharge limits
  7. Signs of a damaged pack
  8. Cycle life and ageing
  9. Disposal
  10. If a pack starts to smoke or swell
  11. Safety checklist

LiPo packs power most electric RC planes because they are light and can deliver high current. They also store a lot of energy in a small space, so charging and storage need care. Most of the risks come down to a few habits. This guide covers them.

The most important rule: charge LiPo packs only while you are watching them, on a non-flammable surface, in a LiPo bag or fire-safe container.

How LiPo cells and packs are rated

Each LiPo cell is 3.7 volts nominal, 4.20 volts when fully charged, and about 3.80 to 3.85 volts at storage level. A pack’s voltage is the cell count times the per-cell voltage:

  • 2S: 7.4 volts nominal
  • 3S: 11.1 volts nominal
  • 4S: 14.8 volts nominal
  • 6S: 22.2 volts nominal

Capacity is in milliamp-hours (mAh). The C rating shows how fast the pack can discharge. As a rough guide, the maximum discharge in amps is the capacity in amp-hours times the C rating. A 2200 mAh pack rated 30C would be listed at about 66 amps. Listed ratings are often optimistic, so treat them as upper limits.

Most packs use a balance lead, a small plug with one more wire than the pack has cells. Balance charging uses that lead to monitor each cell.

Choosing a balance charger

Use a charger with a LiPo balance mode. A universal charger can handle LiPo, NiMH, and other chemistries, but the LiPo mode must be set for LiPo. A NiMH or NiCd program is not suitable for LiPo packs.

Make sure the charger supports your pack’s cell count and the charge current you plan to use.

Charging step by step

  1. Check the pack for damage before you connect it. See the signs below.
  2. Set the charger to LiPo balance mode.
  3. Enter the cell count (the S number) and the charge current. Use the pack maker’s recommended rate. A common default is 1C, which means a 5400 mAh pack charges at 5.4 amps. Some packs are rated for more, and some need less.
  4. Make the connection at the junction between the battery lead and the charger lead, not at the charger’s own output. This keeps the charger’s bare red and black ends from touching. Make the same connection when you disconnect.
  5. Connect the balance lead, then start charging.
  6. Stay nearby the whole time. Watch the voltage, the current, and the pack’s temperature. A pack that gets hot needs attention.
  7. Stop the charge when the charger indicates it is complete.
  8. Let the pack cool to room temperature before you charge it again or fly it.

Balance mode is the one most pack makers recommend. Fast-charge modes can finish sooner, but they may reduce the capacity you get.

Charging rules to keep

  • Never charge a LiPo pack unattended.
  • Never charge a damaged, puffed, or crash-damaged pack.
  • Do not charge below about 0 °C (32 °F). Warm a cold pack to room temperature first.
  • Keep the charger’s safety features on. A safety timer exists to catch a defective pack.
  • Do not charge a pack in a vehicle, on a bed, or near anything that burns.

Storage charge

A pack that will sit unused for more than a few days should be storage-charged. Most chargers have a storage program that brings each cell to about 3.80 to 3.85 volts. Storing a LiPo fully charged speeds up its degradation, so do not leave packs at full charge in the cupboard.

Store packs cool, in a LiPo bag, an ammo can, or a metal container, away from anything flammable. Keep the storage area dry and out of direct sunlight.

Flying and discharge limits

A common rule is to use about 80 percent of the pack’s capacity. That leaves a reserve of about 20 percent for the landing. Set a low-voltage alarm on the transmitter or the ESC, and use telemetry if your system supports it.

Each cell should stay above its minimum voltage, which many manufacturers put at about 3.0 volts under load. Many pilots set a higher floor, around 3.3 volts under load, to leave a margin. Do not run a pack down to empty.

After flying, let the pack cool before you charge it.

Signs of a damaged pack

Retire a pack that shows any of these signs:

  • It is puffed or swollen.
  • It has dents, cuts, punctures, or crash damage.
  • It gets hot while charging or in use, or it smells unusual.
  • One cell drops in voltage much faster than the others.

A puffed pack is not safe to use once it has been flattened. Flattening does not repair the damage inside.

Cycle life and ageing

A typical LiPo pack lasts about 150 to 300 cycles or more, depending on how it is used and cared for. Rising internal resistance is a sign of ageing. An aged pack sags more under load and gets warmer while flying. A pack that sags more than it used to is near the end of its life.

Disposal

Discharge the pack fully with a discharger before disposal. Then take it to a battery recycling point. Do not rely on salt-water soaking to dispose of a pack. Many manufacturers advise against it.

If a pack starts to smoke or swell

If a pack starts to smoke, swell, or get hot while charging, stop the charger if you can reach it safely. Move the pack away from anything flammable. Keep a bucket of sand nearby for small flames. If a pack is on fire, get clear and call emergency services.

Safety checklist

  • Charge only while you can watch the pack.
  • Use a LiPo bag or a fire-safe container, with a bucket of sand nearby.
  • Never charge a damaged or puffed pack.
  • Let packs cool after flying, and warm cold packs before use.
  • Store packs at storage voltage in a fire-safe container.
  • Retire damaged packs, and take them to a recycling point.

For how the battery fits into the rest of the electrical system, see the RC plane electronics guide. For how pack voltage affects motor choice, see RC plane motor and propeller selection.

The complete guide to electronics

RC Plane Electronics: A Complete Guide to Every Component
Read the guide

Keep exploring

Guides from other topics

All topics →