Building

How to Mount Servos in an RC Plane Wing

How to mount servos in an RC plane wing: mounting methods, hardening screw holes, grommets, horn alignment, throw versus torque and lead routing.

On this page
  1. Choose a mounting method
  2. Plan the servo position and pushrod path
  3. Make the mounting blocks
  4. Harden the screw holes
  5. Use grommets and eyelets
  6. Foam wings
  7. Center the servo and set the arm
  8. Line up the horn with the hinge line
  9. Throw versus torque
  10. Use one servo per aileron
  11. Route the leads and secure connectors
  12. Choose a servo size
  13. Check for binding and set travel limits
  14. Common mistakes
  15. Safety

Choose a mounting method

Common methods are:

  • A servo hatch with mounting blocks. The servo is screwed to hardwood or plywood blocks, which are glued into the wing.
  • A servo tray between ribs. A tray spans the ribs and carries the servo.
  • A pocket cut in foam. Used on foam wings.
  • A servo frame or cover kit. A prefabricated frame that fits the wing.

Choose the method that suits your wing. Built-up balsa wings suit trays and blocks. Foam wings suit pockets.

Plan the servo position and pushrod path

Before you cut anything, check where the servo will sit, how the pushrod will reach the horn, and whether the lead can get back to the receiver. A straight pushrod path with few bends gives the most accurate control.

Make the mounting blocks

Use hardwood or plywood blocks, not soft balsa. Glue them to the wing structure with epoxy or aliphatic glue. Position the servo so it sits square, and make sure the screws pull into the blocks, not into the wing skin.

Harden the screw holes

Pre-drill each screw hole. Run the screw in, then back it out. Wick thin CA into the hole, let it cure, then refit the screw. The hardened threads hold better and are less likely to strip.

Use grommets and eyelets

Rubber grommets with brass eyelets isolate the servo from vibration. Vibration can damage servo gears and electronics over time, especially on glow and gas models. Fit each eyelet from the underside, with its flange against the mount.

Tighten the screws only until they are snug. A crushed grommet loses its damping.

Foam wings

In a foam wing, wrap the servo in tape or heat-shrink, then glue it in with hot glue or a foam-safe adhesive. A removable install means you can replace the servo later without cutting the wing apart.

Center the servo and set the arm

Center the servo with a radio or a servo tester before you fit the arm. At neutral, the servo arm and the control horn should sit perpendicular to the pushrod. That gives equal travel in both directions.

Line up the horn with the hinge line

The pushrod hole in the control horn should line up over the hinge line. That gives equal up and down throw.

Throw versus torque

The holes you choose change throw and torque:

  • A servo arm hole closer to the servo output gives less throw at the control surface, but more torque and finer control.
  • A control horn hole farther from the hinge also gives less throw, but more torque at the surface.

Choose holes to suit the control surface. Large, heavy surfaces need more torque, and small surfaces need less.

Use one servo per aileron

Where possible, use one servo per aileron. That allows flaperons, differential throws and the full range of mixes. See RC plane flaps for how flaperons and flap servos work.

Route the leads and secure connectors

Pull the servo lead through the wing with a string, or leave a tube in place during the build. Secure extension connectors with heat-shrink, safety clips or tape, so they can’t come apart in flight.

Choose a servo size

  • Micro servos (about 9 g) suit park flyers.
  • Standard or mini servos suit 40-size sport planes.
  • High-torque metal-gear servos suit large scale and 3D models.

These are typical sizes. Check the plan or kit for the recommended servo.

Check for binding and set travel limits

At neutral and at each end of travel, the servo should not buzz or strain. If it does, check the linkage for binding. Set travel limits in the radio so the servo can’t drive the control surface past its stop.

Common mistakes

  • “Glue the servo straight to the wood.” You can’t remove it if it fails. Use screws, or tape the servo in first.
  • “A longer servo arm is free throw.” It reduces torque and resolution.
  • “Grommets are optional.” Vibration damages servo gears over time.
  • “Wrap it tight.” A crushed servo case can bind its gears.

Safety

Keep servo leads clear of moving parts and hot surfaces. A pinched lead can fail intermittently, so check the lead routing again after the first test.

The complete guide to building

Building RC Planes: Balsa Kits, Materials and Techniques
Read the guide

Keep exploring

Guides from other topics

All topics →