FPV and Drones

FPV RC Planes: Setting Up a Fixed-Wing or Pusher Plane for FPV

How to set up a fixed-wing or pusher RC plane for FPV: airframe choice, flight controller and GPS, center of gravity, setup order, and safe first flights.

On this page
  1. What an FPV plane is
  2. Pusher or conventional layout
  3. Choosing an airframe
  4. Kit or plug-and-play (PNP)
  5. Video and control gear
  6. Flight controller, GPS, and return-to-home
  7. Power: LiPo vs Li-ion and flight time
  8. Set the center of gravity
  9. Setup order and bench tests
  10. Range check and first flights
  11. Common mistakes
  12. Legal basics: line of sight
  13. Choosing your next step

What an FPV plane is

An FPV plane is a fixed-wing aircraft with a camera and video transmitter, flown while you watch the live video in goggles or on a screen. It is different from an FPV multirotor. A plane has wings and control surfaces, flies forward, and needs airspeed to stay in the air. Fixed-wing planes can glide when power is lost, which is one way they differ from multirotors.

If you are new to FPV in general, read building an FPV drone and how to fly an FPV drone for the first time first. The plane setup below assumes you know the basic goggles and radio workflow.

Pusher or conventional layout

A conventional plane has its propeller at the front. A pusher has its propeller at the rear, pushing the plane through the air. For FPV, pushers have three practical benefits:

  • Prop protection. The propeller sits behind the wing or tail boom, so a nose-first landing is less likely to break it.
  • Camera view. The nose camera sees no propeller.
  • Hand launch. A rear prop keeps the nose clear, but it spins just behind your launching hand, so keep your fingers clear.

Pushers are not inherently harder to fly. Thrust line and center of gravity matter more than the layout. A pusher motor is often mounted above the center of gravity, so it may need downthrust or alignment to avoid a nose dive when you add throttle.

Choosing an airframe

Beginner-friendly FPV planes include:

  • Foam trainers and foamboard planes. Cheap and easy to repair. A foamboard trainer is a common first plane.
  • Small pusher foam planes. Models such as the ZOHD Nano Talon (about 860 mm) are popular for compact FPV flying.
  • Larger foam planes. Volantex Ranger models around 1,600 to 2,000 mm carry more electronics and fly longer.
  • Flying wings. Simple and fast, with elevons instead of separate ailerons and elevator.
  • V-tail and conventional-tail planes. Typically slower and more stable than flying wings.

Choose based on your skill level and the space you have.

Kit or plug-and-play (PNP)

A kit comes as bare parts, and you add your own motor, speed controller, servos, and electronics. A plug-and-play (PNP) airframe comes with the motor, speed controller, and servos installed, so you only add the radio, flight controller, video, and battery. PNP is simpler for a first FPV plane. Kits give you more control over the electronics.

Video and control gear

  • Camera and video transmitter (VTX). You can choose analog or a digital HD system such as DJI O4, Walksnail, or HDZero. All operate on 5.8 GHz in common setups.
  • Antennas. Use circular polarized antennas, and match the receive side (RHCP or LHCP) to the VTX. Mount the receiver and VTX antennas apart and away from carbon parts and batteries.
  • Control link. ExpressLRS 2.4 GHz is common. A 900 MHz link such as Crossfire can penetrate better at longer range.

For how analog and digital video compare, see analog vs digital FPV.

Flight controller, GPS, and return-to-home

Plane flight controllers commonly run INAV or ArduPilot. A good plane controller provides stabilization, on-screen display (OSD), and GPS return-to-home (RTH). Matek F405-WMN and similar wing-class boards are common choices.

Mount the GPS module away from the VTX and power wiring. Wait for a stable fix before flying, and do not assume return-to-home will always work. Verify the fix (a common target is 6 to 8 or more satellites) and test the failsafe before any flight. RTH is a backup, not a guaranteed save.

Power: LiPo vs Li-ion and flight time

Plane setups often run on 3S or 4S power. LiPo packs deliver more punch, which helps climbs and launches. Li-ion packs (18650 or 21700 cells) give longer cruise times, with a common range of roughly 40 minutes or more compared with 15 to 30 minutes on LiPo. Flight time varies a lot with airframe and throttle use.

More battery is not always more flight time. Extra weight raises wing loading, which increases stall speed and can cut flight time.

Set the center of gravity

Set the center of gravity (CG) to the manufacturer’s specification. Many planes list it as a percentage of the mean aerodynamic chord, often around 25 to 33 percent back from the wing’s leading edge. Move the battery, not the control surfaces, to adjust it. The center of gravity guide shows how to find the balance point.

A plane that is nose-heavy will be sluggish and hard to flare. A plane that is tail-heavy can become unstable. Recheck CG after you add or move the camera, VTX, or GPS.

Setup order and bench tests

Set up in this order:

  1. Servo direction and throws. Check that each control surface moves the right way and has the right range.
  2. Control surface center. Set the surfaces neutral in the flight controller.
  3. Flight controller orientation. Tell the controller how it is mounted.
  4. Accelerometer calibration. Run the six-position calibration, then set the level reference with the plane in its flying attitude.
  5. Failsafe. Set return-to-home or a glide-and-hold failsafe.
  6. OSD. Set the on-screen display for battery, GPS, and link information.

Before the first flight, test the stabilized mode on the bench. Tilt the plane and watch the surfaces. They should correct the tilt in the right direction. If a surface moves the wrong way, fix the setting before you fly.

Range check and first flights

Range-check the radio link before every first flight of a new setup. Then fly the first sessions in line of sight with a spotter, and switch to goggles only after the plane is stable in your hands.

For a hand launch, use full throttle and launch with the wings level and a slight nose-up angle. Keep your hand clear of the propeller, and consider a launch delay or a glove. Pusher props can injure fingers on launch.

Plan your first flights in the same wind and open space you would use for any new aircraft. Light wind, no obstacles, and room to land are the basics.

Common mistakes

  • Trusting return-to-home without testing it. Verify GPS fix and failsafe before flight.
  • Skipping the CG check. A plane flown out of CG is hard to control.
  • Adding more battery to chase flight time. Extra weight can make the plane slower and harder to handle.
  • Flying the first session in goggles. Start in line of sight.
  • Ignoring the pusher prop on launch. Keep hands clear.

Flying a plane with FPV does not change the rules. In most countries, recreational flying must stay within visual line of sight, and goggles block your own view, so a visual observer is required in many places. Long-range plane flying often goes beyond visual line of sight, which most countries restrict for recreational pilots. For the details, see is long range FPV legal? Check your national aviation authority for the current rules.

Choosing your next step

Start with a simple foam trainer or small pusher, learn to fly it in line of sight, then add FPV once the setup is reliable. Compare analog and digital systems before you buy any gear, and choose goggles that match your video system in FPV goggles compared. For budget planning, see cheap FPV.

The complete guide to fpv and drones

Getting Into FPV on a Budget: Drones, Planes and Gear
Read the guide

Keep exploring

Guides from other topics

All topics →