Short answer: there isn’t one best airfoil
No single airfoil is best for every RC plane. The right shape depends on the plane’s purpose, its speed and size, and the pilot’s skill. A gentle trainer needs different lift and stall behavior from a fast aerobatic model or a thermal glider.
For many builders, a sensible starting point is a flat-bottom airfoil for a trainer, a semi-symmetrical airfoil for a sport plane, and a symmetrical airfoil for aerobatics. Build accuracy, balance and wing loading often matter more than the exact airfoil.
Flat-bottom airfoils
A flat-bottom airfoil, such as the Clark Y (about 11.7% thick), gives plenty of lift at low speed. It stalls gently and is easy to build on a flat board. That is why it is common on trainers and high-wing sport planes.
Flat-bottom airfoils can fly inverted, but they need more down elevator to do it.
Semi-symmetrical airfoils
A semi-symmetrical airfoil balances lift with the ability to fly inverted. It is a common choice for sport and low-wing planes.
Symmetrical airfoils
A symmetrical airfoil has the same shape on top and bottom, so it flies the same way right-side up or inverted. That suits aerobatic and 3D models. Typical examples are the NACA 0012 to 0018 family. A symmetrical section produces lift through its angle of attack rather than through camber.
Undercambered airfoils
Undercambered airfoils have a bottom surface that curves inward, so it is concave rather than flat. They give high lift at low speed, which suits slow free-flight and vintage models. They also create more drag and are harder to cover, so they rarely suit most RC planes.
Reflexed airfoils
Reflexed airfoils, such as MH45, MH60 and E325, have an upturned trailing edge. That upturn gives a flying wing pitch stability without a separate tailplane. For flying-wing design, see RC glider and flying wing plans.
Thin cambered airfoils
Thin cambered airfoils, such as SD7037, RG15 and the AG series, suit thermal and electric gliders. They produce low drag at low speed. Gliders usually use sections about 7 to 10% thick.
Thickness, stall and speed
Thickness changes how a wing behaves:
- Thicker sections stall more gently and are easier to build stiff and light. They also create more drag.
- Thinner sections are faster with less drag, but they stall more suddenly.
As rough ranges, gliders use about 7 to 10%, trainers and sport planes about 12 to 15%, and aerobatic or 3D planes about 14 to 18%. Designs vary.
Low Reynolds numbers
RC planes fly at low Reynolds numbers, roughly 50,000 to 500,000. At those values, airflow behaves differently from full-size aircraft, so full-scale airfoil data can mislead. Where you can, use airfoil data measured at model Reynolds numbers.
Stepped airfoils on foam board
Many foam-board builds use KF (Kline-Fogleman) stepped airfoils. They are easy to make from flat sheets, but they are not efficient. They suit a simple first build.
Choosing for your plane
- Trainer: flat-bottom, thicker and forgiving.
- Sport: semi-symmetrical, balancing lift and inverted ability.
- Aerobatic: symmetrical, about 14 to 18% thick.
- Glider: thin cambered, for low drag.
- Flying wing: reflexed.
Check the wing loading too. The wing loading guide explains why a lighter wing suits beginners. Then check the balance point with the center of gravity guide.
Tools for looking up and plotting airfoils
- Profili for drawing and plotting airfoil sections
- XFLR5 for analyzing wing and airfoil performance
- UIUC Airfoil Database for airfoil coordinates and data
Common misconceptions
- “Flat-bottom airfoils can’t fly inverted.” They can, with more down elevator.
- “Symmetrical airfoils make no lift.” They lift through their angle of attack.
- “Full-scale airfoils work as well on models.” Many perform poorly at model Reynolds numbers.
- “Undercambered is best for slow flight on every model.” Its drag and building difficulty rule it out for most RC planes.