Building

Finding the Center of Gravity on an RC Plane

How to find the center of gravity on an RC plane: start with the plan, use the mean aerodynamic chord, balance ready to fly, and fix the balance safely.

On this page
  1. Start with the plan’s CG
  2. Typical ranges by plane type
  3. Find the mean aerodynamic chord
  4. Balance the plane ready to fly
  5. Balancing tools
  6. Level on the marks, then check the side balance
  7. Fix the balance
  8. Mark the CG and the battery position
  9. Nose-heavy versus tail-heavy
  10. Common mistakes
  11. Safety

Start with the plan’s CG

The plan or manual gives the center of gravity (CG) for your plane. Use that figure. It overrides any general rule, including the ranges in this article.

Typical ranges by plane type

These are rough guides only:

  • Conventional planes: about 25 to 33% of the mean aerodynamic chord (MAC) back from the leading edge.
  • Trainers: often about 25 to 30%.
  • Sport and aerobatic: often about 28 to 33%.
  • Flying wings: much farther forward, often about 15 to 25%.

Some 3D models balance farther back. Follow the plan in every case.

Find the mean aerodynamic chord

For a rectangular wing, the MAC equals the root chord, so measure the chord at the root.

For a tapered wing, use this formula:

MAC = (2/3) × Cr × (1 + λ + λ²) ÷ (1 + λ)

Here Cr is the root chord, and λ (lambda) is the tip chord divided by the root chord.

To locate the MAC across the span, use:

y = (b/6) × (1 + 2λ) ÷ (1 + λ)

Here b is the full wingspan, and y is the distance from the centerline to the MAC. Online CG calculators also handle swept and tapered wings, which is a useful check on your figures.

Balance the plane ready to fly

Balance the plane in the state you will fly it:

  • The battery is installed.
  • The fuel tank is empty. Glow and gas models balance with an empty tank.
  • The plane is upright, with nothing loose inside.

Balancing tools

  • Fingertips placed at the marked points, for a quick check
  • A CG balancer, such as the Great Planes C.G. Machine
  • A plumb-line method, which hangs the plane from a point to find its balance

Level on the marks, then check the side balance

Balance the plane level on the marks. A slightly nose-down attitude at the CG mark is acceptable.

Check the side-to-side (lateral) balance too. Support the plane at the nose and the tail, and check that the wings sit level. If one wingtip drops, add a little weight to the lighter side.

Fix the balance

Move the battery first, because it is the easiest component to shift. Then move other components, such as the receiver or the speed controller. Add weight only as a last resort, and place it where it does the least harm.

Weight added to fix the balance also raises the wing loading. See the wing loading guide.

Mark the CG and the battery position

Mark the CG on the fuselage, and mark the battery position too. The marks make it easy to repeat the balance after you change batteries or add gear.

Nose-heavy versus tail-heavy

Nose-heavy and tail-heavy are not equally bad. A tail-heavy plane can be uncontrollable, while a nose-heavy plane is safer to fly.

Never fly a first flight tail-heavy. Err toward nose-heavy, within the plan’s range.

Common mistakes

  • “Nose-heavy and tail-heavy are equally bad.” A tail-heavy plane can be uncontrollable.
  • “Balance from the trailing edge.” Measure from the leading edge at the correct chord.
  • “Tapered wings balance at the root percentage.” Use the MAC.
  • “Balance it with fuel in.” Glow models balance with the tank empty.

Safety

Never fly a plane you have not balanced to the plan’s figure, and never fly a first flight tail-heavy.

The complete guide to building

Building RC Planes: Balsa Kits, Materials and Techniques
Read the guide

Keep exploring

Guides from other topics

All topics →