Building

How to Cover an RC Plane with MonoKote and a Covering Iron

Step-by-step MonoKote covering with a covering iron: prep, iron temperature, tacking, shrinking, overlaps, bubble and wrinkle fixes, and trim.

On this page
  1. What MonoKote is
  2. Tools you need
  3. Prepare the surface
  4. Set the iron and test on scrap
  5. Cut oversize and tack the edges
  6. Seal the perimeter, then shrink from the center
  7. Overlaps and covering order
  8. Fix bubbles and wrinkles
  9. Trim and stripes
  10. Common mistakes
  11. Safety

What MonoKote is

MonoKote is a heat-shrink covering film from Top Flite, now a Horizon Hobby brand. It is a polyester film with adhesive on the back that stays inactive until you heat it. When you apply heat, the film shrinks and bonds to the balsa or foam underneath.

Many builders use it on medium and large models. Lighter models often use lower-heat films.

Availability is worth checking. A forum discussion reports that the original US manufacturing plant has closed and that older stock is harder to find. We have not confirmed this, so check current stock before you order a large roll. UltraCote, Oracover and other heat-shrink films follow the same basic method, but each has its own temperatures, so follow the maker’s chart.

Tools you need

  • A covering iron with a protective sock. Don’t iron film bare.
  • A heat gun for shrinking open spans and curves
  • A fresh #11 blade and a straightedge
  • Pins and a clean, dust-free bench

The tools guide covers the rest of the list.

Prepare the surface

Film shows every flaw underneath it. Fill dents, sand the structure to about 320 to 400 grit, then remove all dust with a vacuum or tack cloth. Dust under the film shows as bumps and can cause bubbles.

Set the iron and test on scrap

Iron temperature depends on the film and the iron. As an approximate guide, MonoKote is often tacked and sealed at about 225 to 250°F, and shrunk at about 300 to 350°F. Don’t exceed the maker’s limit. Test your settings on a scrap piece of covered balsa before you start, and keep the iron moving.

Cut oversize and tack the edges

Cut each panel about 1 inch larger than the surface it covers. Peel the backing as you go. Tack the corners and edges with the iron at low to medium heat. Don’t seal everything at once, or you may trap air.

Seal the perimeter, then shrink from the center

Seal the perimeter with the iron, then work from the center outward. Seal over the framework first, so the open bays tighten evenly.

Use the heat gun on open spans and wingtips, where a flat iron can’t follow the curve. Keep the gun moving so the film doesn’t scorch.

Overlaps and covering order

  • Seam overlap is about 1/8 to 1/4 inch (3 to 6 mm). At the leading edge, use about 1/4 inch or more.
  • Overlap seams so the airflow passes over the edge, not into it. The front piece goes on top.
  • A common order is the wing bottom first, then the top, which overlaps the bottom at the leading edge. For the fuselage, go bottom, sides, then top.
  • Cover control surfaces separately before you hinge them.

Fix bubbles and wrinkles

Prick trapped air bubbles with a pin, then re-iron the spot. Wrinkles that show up later in sun or heat can often be re-shrunk with the iron.

Shrinking does not fix a warped wing. Uneven heat can make a warp worse, so check the structure for straightness before you cover it.

Trim and stripes

Trim lines and stripes are easier to place if you lay them on with a film of soapy water or glass cleaner. Position the trim, squeegee out the liquid, let it dry, and then seal the edges with the iron.

Trim the excess with a fresh blade and a straightedge. Cut lightly so you don’t score the wood underneath.

Common mistakes

  • “Hotter is faster.” Too much heat pulls seams open, burns through the film or warps light structures.
  • “Ironing over dust is fine.” Every speck shows through as a bump.
  • “All films are the same.” Temperatures and adhesives differ between brands.

Safety

  • Irons get hot. Use a stand, and never leave one on unattended.
  • Heat guns can burn skin and melt film. Keep them moving and away from your hands.

The complete guide to building

Building RC Planes: Balsa Kits, Materials and Techniques
Read the guide

Keep exploring

Guides from other topics

All topics →