Building

How to build a balsa wood model plane?

How to build a balsa wood RC plane from a kit: workspace, fuselage and wing framing, dihedral, glues, covering, balancing and build time.

On this page
  1. Short answer: build from a kit, on a flat board, one section at a time
  2. Pick your type
  3. Gather tools and set up a flat workspace
  4. Choose balsa by weight and grain
  5. Build the fuselage
  6. Build the wings
  7. Join the wings with a dihedral brace
  8. Build the tail
  9. Pick the right glue for each joint
  10. Sand, then cover
  11. Install hinges, servos and power
  12. Balance and check for warps
  13. How long it takes
  14. Common mistakes
  15. Safety

Short answer: build from a kit, on a flat board, one section at a time

To build a balsa wood model plane, work on a flat, unwarped board. Lay the plans under clear plastic or wax paper, cut out the parts for one section at a time, and frame each section over the plan. Build the fuselage and wings, join the wings with a dihedral brace, build the tail, then sand, cover and install the hinges, radio and power. Balance the plane at the plan’s center of gravity before you fly it.

Pick your type

There are three basic types of balsa model plane:

  • Static display models, built to look good on a shelf.
  • Rubber-powered free flight models, such as classic Guillow’s designs.
  • RC kits, built to be flown with a radio, such as a SIG Kadet-style trainer.

This guide covers the RC kit. Static and rubber models follow a similar framing sequence, but they skip the radio and power install.

Gather tools and set up a flat workspace

Choose a well-lit area with an outlet nearby, and a table you can work at for hours. You need a building board that pins can go into, such as a cork ceiling tile. Add a sharp hobby knife, a fine razor saw, sandpaper, T-pins, a ruler, a straightedge and a triangle. The tools guide lists the full set.

Protect the plans with wax paper or clear plastic wrap, so glue doesn’t stick the plane to them.

Choose balsa by weight and grain

Use light A-grain or B-grain sheet for sheeting, C-grain for ribs, and harder balsa or spruce for spars. Sort parts by weight, because balsa varies a lot between sheets. The guide to building RC planes from balsa kits explains density and grain in more detail.

Build the fuselage

Build the fuselage over the plan. Some builders make both sides over the plan, one on top of the other. Join the two sides with the formers, then check that the structure is square with a triangle before the glue sets.

Build the wings

  • Pin the bottom spar flat over the plan.
  • Set the ribs, checking each one against the plan.
  • Glue the top spar and the leading and trailing edges.
  • Add the shear webs, and sheet the wing if the plan calls for it.

Join the wings with a dihedral brace

Join the wing halves with a dihedral brace and 30-minute epoxy. Block up the tips to the plan’s dihedral. The dihedral guide explains how plans give dihedral and how to convert it to a tip height.

Build the tail

Build the tail flat on the plan. Check that the stabilizer is square to the fin and parallel to the wing. A crooked fuselage or tail makes trimming harder for the life of the model.

Pick the right glue for each joint

Use thin CA for well-fitted joints, aliphatic glue where you have time to adjust, and epoxy where strength is critical. Give each joint its full cure time. CA sets fast, but aliphatic glue and epoxy need longer. The gluing comparison explains set times and cautions.

Sand, then cover

Sand each part with a block or T-bar, moving from about 150 grit to 220 and then to 320 before covering. Tissue and dope suit small or rubber models. RC models usually use heat-shrink film. The MonoKote covering guide shows how to cover with film and a covering iron.

Install hinges, servos and power

Install the hinges, horns and pushrods. Mount the servos securely, then install the motor or engine, radio and battery. Set the control throws from the plan or manual. The servo mounting guide covers the details.

Balance and check for warps

Check for warps by sighting along the wing and the tail, and correct any warp before you fly.

Balance the plane at the CG shown on the plan, which is typically 25 to 33% of the mean aerodynamic chord, with the battery installed. Err toward nose-heavy within the plan’s range. See finding the center of gravity.

How long it takes

A small rubber model can take a few evenings. An RC trainer kit takes about 40 to 100 hours or more, depending on your skill and the kit.

Common mistakes

  • “Glue the joint and fill the gaps.” Cut parts to fit tightly. Glue does not fill gaps well.
  • “Leave the parts pinned for a few minutes.” CA sets fast, but aliphatic glue and epoxy need their full cure time.
  • “Skip squaring the fuselage.” A crooked fuselage causes trim problems for the life of the model.
  • “Balsa is too fragile for RC.” Properly braced balsa structures are durable.

Safety

  • Cut on a mat, away from your body.
  • Wear a dust mask while sanding.
  • Ventilate when using CA.

The complete guide to building

Building RC Planes: Balsa Kits, Materials and Techniques
Read the guide

Keep exploring

Guides from other topics

All topics →