Building

Wing Loading for RC Planes: How to Calculate It and Why It Matters

How to calculate RC wing loading and wing cube loading, measure wing area, compare planes of different sizes, and see how loading changes stall speed.

On this page
  1. The formula
  2. A worked example
  3. Use the flying weight
  4. How to measure wing area
  5. Typical ranges
  6. Wing cube loading
  7. What loading changes in flight
  8. Changing the loading
  9. Common mistakes
  10. Tools for the calculation

The formula

Wing loading is the flying weight divided by the wing area.

  • Imperial: ounces per square foot (oz/ft²) = weight (oz) ÷ wing area (ft²)
  • Metric: grams per square decimeter (g/dm²) = weight (g) ÷ wing area (dm²)

One oz/ft² is about 3.05 g/dm². Wing loading tells you how much weight each square foot of wing has to support in flight.

A worked example

Say a plane weighs 64 oz and has a wing area of 576 square inches.

  • 576 in² ÷ 144 = 4 ft²
  • 64 oz ÷ 4 ft² = 16 oz/ft²

Use the flying weight

Use the all-up flying weight: everything installed and ready to fly, including the battery or a full fuel tank. A dry weight understates the loading and makes comparisons wrong.

Every ounce added during the build raises the loading, so keep track of weight as you go.

How to measure wing area

Wing area is usually taken as the projected area of the wing, including the section that passes through the fuselage. Manufacturers and rule sets differ on the details. Some measure flat, some measure projected through the dihedral, and some treat the fuselage section differently. Check the manufacturer’s figure, and note which convention you used when you compare planes.

Tail surfaces are normally left out of wing loading unless a specific rule or reference includes them.

Typical ranges

These are rough ranges, and they vary widely with size:

Plane type Approximate loading (oz/ft²)
Indoor and micro under 5
Park flyers and gliders about 6 to 12
Trainers about 12 to 20
Sport and aerobatic about 18 to 28
Warbirds and jets about 25 to 40 or more

Other sources use slightly different bands, so treat these as a starting point, not a rule.

Wing cube loading

Wing loading alone does not compare planes of different sizes well, because a large plane tolerates a higher wing loading than a small one. Wing cube loading (WCL) accounts for size:

WCL = weight (oz) ÷ (wing area in ft²)^1.5

A rough WCL guide:

  • Under 4: gliders and floaters
  • 4 to 7: trainers and park flyers
  • 7 to 10: sport and aerobatic
  • 10 to 13: scale and warbirds
  • Above 13: fast or expert-only

Two planes with the same 16 oz/ft² loading can fly very differently, one at 30 inches of span and one at 80 inches. WCL helps you see that difference.

What loading changes in flight

  • Stall speed rises with the square root of wing loading. Double the loading and stall speed rises by about 1.41 times. Airfoil and flaps also change stall speed, so loading is only part of the picture. The airfoil guide explains how the section affects stall behavior.
  • Lower loading gives slower landings and easier handling in light wind, but less penetration in strong wind.
  • Higher loading flies faster and holds its line better in gusts, but it needs longer, faster landings. Tip stalls are more abrupt.

Changing the loading

Removing weight is the most direct way to lower loading, and adding weight raises it. Weight added to fix the balance raises the loading too, so move the battery or other components first. The center of gravity guide explains the order to work in.

Common mistakes

  • “16 oz/ft² is light for every plane.” The same loading flies very differently on a 30-inch plane and an 80-inch plane. Compare with WCL.
  • “Wing loading alone sets stall speed.” The airfoil, flaps and wing shape matter too.
  • “Use the dry weight.” Always use the ready-to-fly weight.
  • “Battery weight doesn’t matter on electrics.” On electric planes, the battery often dominates the loading.

Tools for the calculation

Online calculators, such as the Stevens Aeromodel and FlyRC wing loading calculators, do the arithmetic. Check that the calculator uses the same units and the same area convention as your figures.

The complete guide to building

Building RC Planes: Balsa Kits, Materials and Techniques
Read the guide

Keep exploring

Guides from other topics

All topics →