What EPO foam is
EPO stands for expanded polyolefin. It is a molded foam that is flexible, tough and resilient, and it bounces back from knocks better than many foams. Many foam ARF and PNP planes use it, including models from E-flite, Volantex, FMS and Freewing.
EPO versus other foams
| Foam | What it is | Notes |
|---|---|---|
| EPS | Bead foam | Brittle; standard CA can melt it |
| EPP | Expanded polypropylene | Very flexible and near-indestructible |
| EPO | Expanded polyolefin, molded | Flexible and stiff; used for many kit parts |
| XPS or Depron | Smooth sheet foam | Common for scratch builds |
| Foam board | Paper-faced board, about 3/16 inch (5 mm) | Basis of many beginner builds |
These foams differ a lot in strength, finish and glue compatibility. Check which foam you have before you choose a glue or a paint.
What building an EPO plane means
EPO usually comes as molded parts. Most EPO planes are kit or ARF builds, so the job is mainly assembly, reinforcement and repair, rather than building from scratch. Scratch builders more often use Depron, foam board or EPP sheet.
Glues that work on EPO
- Medium CA with accelerator
- Foam-safe CA
- Epoxy
- UHU Por and contact glues
- Foam-Tac
- Low-temperature hot glue
Test any glue on a scrap piece first. Standard CA can attack some foams, so don’t assume it is safe on EPO. Use accelerator sparingly, because excess kicker can heat and weaken foam joints.
Reinforce the structure
Foam is soft where loads concentrate, so strengthen those areas:
- Carbon fiber spars or tubes along the wing
- Fiberglass tape over joints
- Plywood at the motor mount and wing bolt points
Hinges
Common hinge options are:
- Molded foam hinges, which often come with the kit
- Packing tape or Blenderm
- CA hinges, set in slots cut in the foam
Control horns
Install control horns with a plate backing or as through-bolted pairs, so the load spreads across the foam instead of pulling through it.
Clean and paint
Clean molded EPO with isopropyl alcohol or soapy water before you paint. Mold release on the surface blocks adhesion, so remove it first.
Paint with water-based acrylics. Solvent-based spray paints can attack some foams, so test on scrap before you spray a whole airframe.
Power and balance
Typical electric power for a sport foam model is roughly 100 to 150 W/lb, with trainers at the lower end and 3D models higher. This is a rough guide, so follow the kit’s recommendation.
Balance the plane at the CG the manual gives. Foam builds often need the battery fully forward to reach it. See finding the center of gravity.
Building from foam board
If you want to scratch-build instead, foam board such as Dollar Tree or Adams Readi-Board is the usual starting point. The basic steps are to cut the parts, score and fold the foam, install the motor mount, hinge the control surfaces, fit the servos and electronics, and then balance the plane.
Electronics for a small foam-board plane often include a brushless motor (around 1450 to 2200 KV for many small builds), a 12 to 20 A speed controller with a built-in BEC, a 3S LiPo, two or three 5 to 9 g micro servos, and a 4 to 6 channel radio. Choose the motor, speed controller and battery for your plane’s size and propeller, and check the parts list for the design you are building. The motor and propeller selection guide explains how to match them.
Cutting foam
Cut EPO with a sharp blade in several light passes, rather than one hard cut. A hot wire or hot knife works well on EPS and XPS. Hot-wire cutting releases fumes, so ventilate and avoid breathing them.
Repairs
EPO repairs well with CA plus kicker, or with a foam glue. Use light kicker, and let the joint cure fully before you load it. Heavy kicker can heat and weaken the foam around the joint.
Common mistakes
- “All foam is the same.” EPS, EPP, EPO and XPS differ greatly in strength, finish and glue compatibility.
- “Foam planes can’t be repaired.” EPO repairs well with CA plus kicker or foam glue.
- “Paint with any spray can.” Solvents can dissolve some foams.
- “Hot glue works for everything.” It adds weight and can soften in a hot car.
Safety
- Hot-wire cutting releases fumes. Ventilate, and avoid breathing them.
- Keep hot tools on a stand in a safe spot, and unplug them when you finish.
- Keep solvent-based paints away from heat and open flame.