Building

Essential Tools for Building RC Airplanes

The core tools for building RC airplanes: cutting, building board, measuring, adhesives, covering and electronics tools, plus what you can skip at first.

On this page
  1. Start with the core tools
  2. Cutting and shaping
  3. A flat, reliable building board
  4. Clamps and holding tools
  5. Measuring and checking square
  6. Adhesives and what each one is for
  7. Covering tools
  8. Electronics and hardware tools
  9. A field repair kit
  10. Tools you can skip at first
  11. Safety

Start with the core tools

Most kits can be built with a small set of tools: a sharp knife, a flat board, pins, sandpaper, glue and a covering iron. You do not need a full workshop to start. Add specialist tools as your builds call for them.

Cutting and shaping

  • Hobby knife with #11 blades. X-Acto or a similar knife. Change blades often, because a dull blade crushes balsa instead of cutting it.
  • Single-edge razor blades for slicing balsa sheet and strip.
  • Fine-tooth razor saw for spars, hardwood and plywood.
  • Sanding blocks and T-bar sanders. Use about 80 to 150 grit for shaping, 220 for finishing, and 320 to 400 before covering.
  • Rotary tool or drill for slotting and trimming, with a pin vise and small bits for precise holes.

A flat, reliable building board

A flat board is the base of a straight build. Options include a cork or ceiling tile on plywood, Homasote, or a magnetic board. Lay clear plastic or wax paper over the plans so glue does not stick to them, then pin the parts down with T-pins.

Any flat table is not enough. A warped board gives you a warped wing, so check the board with a straightedge before you start.

Clamps and holding tools

  • Clothespins, spring clamps and small bar clamps
  • Rubber bands and masking tape
  • A small swivel vise or quick-grip clamps for holding parts while glue cures
  • A foam-padded cradle or stand to support the fuselage during assembly

Measuring and checking square

  • A steel straightedge, 24 to 36 inches long
  • A machinist’s square and 90° and 45° triangles
  • A digital caliper or steel ruler
  • A CG balancer or marked fingertip points for finding the center of gravity
  • A throw meter or ruler for setting control surface travel

Adhesives and what each one is for

  • Thin, medium and thick CA with accelerator for framing and quick tacks.
  • Aliphatic (yellow) glue for joints you can sand.
  • 5-minute and 30-minute epoxy. Use the 5-minute for non-critical jobs and the 30-minute for firewalls and other high-stress joints.
  • CA debonder for cleanup and for freeing skin or parts that bond by accident.
  • Foam-safe CA and foam glue if you build with foam.

The gluing comparison explains when each one works best.

Covering tools

  • A covering iron with a protective sock for tacking and sealing film. A household iron is hard to control at covering temperatures and is too large for curves.
  • A heat gun for shrinking open spans and compound curves.
  • A fresh #11 blade and a straightedge for trimming film.

The MonoKote covering guide shows how these tools work together.

Electronics and hardware tools

  • Metric hex drivers (roughly 1.5 to 3.0 mm) and small Phillips screwdrivers
  • Needle-nose pliers, wire cutters and Z-bend pliers
  • A soldering iron with enough power for large connectors. A rough guide is about 60 W or more for XT60 or EC3 connectors, plus solder and heat-shrink tubing.
  • A servo tester or radio for centering servos before fitting them. See mounting servos in a wing.
  • A battery checker or charger that shows cell voltage (see LiPo charging and storage)

A field repair kit

Keep a small kit at the flying site so a minor problem doesn’t end the day. It can include spare CA with accelerator, a small amount of 30-minute epoxy, spare screws and pushrod hardware, a few servo arms, and a way to re-heat loose film.

Tools you can skip at first

  • “You need a full workshop.” A knife, pins, a flat board, sandpaper, glue and an iron will build most kits.
  • “A household iron works as well as a covering iron.” It is hard to control at covering temperatures.
  • “Cheap blades are fine.” Dull blades crush balsa instead of cutting it.

Expensive power tools and specialist meters can wait until a build needs them.

Safety

  • Wear eye protection with rotary tools and when cutting music wire or carbon.
  • Use a dust mask when sanding balsa, fiberglass or carbon.
  • Ventilate when using CA and soldering.
  • Keep a CA debonder nearby in case skin gets bonded.

The complete guide to building

Building RC Planes: Balsa Kits, Materials and Techniques
Read the guide

Keep exploring

Guides from other topics

All topics →