Choosing a Plane

ARF, RTF and Kit RC Planes: What the Labels Mean

RTF, ARF, BNF, PNP and kit are the labels on RC planes. Here is what each one includes, how much assembly it needs and which suits a beginner best.

On this page
  1. The short answer
  2. RTF: ready to fly
  3. BNF and PNP: you supply the radio
  4. ARF and ARTF: airframe mostly built
  5. Kits: wood or laser-cut parts and plans
  6. Scratch builds
  7. Label comparison
  8. Read the “required to complete” list
  9. Which label should you choose?
  10. Safety checks before flying an ARF or kit

The short answer

The label on an RC plane tells you how much work is left before the first flight. Ready-to-fly (RTF) planes need the least work. Almost-ready-to-fly (ARF) planes need the power system, radio and battery added. Kits need the most work. Manufacturers define these labels in their own ways, so always check the list of what is included.

RTF: ready to fly

An RTF plane comes with everything in the box: the airframe, the power system, servos, receiver, transmitter, battery and charger. Assembly is minimal, often just attaching the wing and tail.

Keep in mind that the transmitter is usually basic, and many pilots upgrade it later. Transmitter AA batteries are sometimes not included.

BNF and PNP: you supply the radio

Two related labels leave out the radio gear.

  • BNF (bind-and-fly) includes a receiver, but not a transmitter. You bind the plane to your own transmitter. The transmitter must speak the same protocol, such as Spektrum DSM2 or DSMX. A BNF Basic plane also leaves out the flight battery and charger.
  • PNP (plug-and-play) has the motor, speed controller and servos installed. You add the receiver, transmitter, battery and charger.

BNF and PNP planes suit pilots who already own a radio. They can be a good buy, but the total cost is higher than the listed price once the missing parts are added.

ARF and ARTF: airframe mostly built

An ARF (almost ready to fly) plane comes with the airframe mostly built and covered. The fuselage, wings and tail are already together. You install the motor or engine, the servos, the radio and the battery, and you may need to glue the wing halves together.

Some manufacturers use variants:

  • ARF+ or ARF Plus includes some parts pre-installed, such as servos or retracts, but leaves the power system to you.
  • ARF bundle includes the airframe plus the required electronics. You still install them and provide your own radio and battery.

Assembly time varies. A foam ARF can take a few hours. A balsa ARF can take 10 to 20 hours or more.

Kits: wood or laser-cut parts and plans

A kit contains the raw parts, often laser-cut or die-cut balsa or plywood, and plans. You build the frame, cover it and install everything. Kits give you the most learning and the most control over repairs.

Build time is measured in tens of hours. A complex scale kit can take 100 hours or more. Kits also need tools, glue, covering material and hardware, which are often not included.

Scratch builds

A scratch build starts from plans or your own design, with no pre-cut parts. Foam-board builds are popular for simple planes, and they are a good way to learn. Scratch builds take the most skill and time.

Label comparison

Label What is included Your work before flying Typical skill
RTF Airframe, power, radio, battery, charger Attach the wing and tail, and charge Beginner
BNF Airframe, power, receiver Add a matching transmitter, battery and charger Beginner with a radio
PNP Airframe, motor, speed controller, servos Add receiver, transmitter, battery and charger Some experience
ARF Airframe mostly built and covered Install power, radio and battery Some experience
Kit Raw parts and plans Build, cover and install everything Intermediate to advanced

Read the “required to complete” list

Each listing should say what you still need to buy. Read that list before you compare prices. A plane that looks cheap may need a radio, battery and charger that together cost more than a ready-to-fly package.

Which label should you choose?

  • If you are new to the hobby, choose RTF. It is the simplest way to start.
  • If you already have a radio, consider BNF or PNP, and check the protocol before you buy.
  • If you enjoy building, an ARF or kit teaches a lot about how the plane works.

For a first plane, see the best ready-to-fly RC planes for your first plane. For budget options, see the best RC planes under $100 and under $200.

Safety checks before flying an ARF or kit

Factory glue joints can be weak, so check them before the first flight. Look at the control horns and hinges, and make sure the servo arms and pushrods are secure. Check the center of gravity and the control throws against the manual. Those checks take a few minutes and can prevent a serious crash.

The complete guide to choosing a plane

The Best RC Planes for Every Skill Level and Budget
Read the guide

Keep exploring

Guides from other topics

All topics →