RC Jets

How much thrust does an RC jet engine have?

Most sport-jet turbines produce roughly 8 to 14 kgf (about 80 to 140 N). Learn how thrust is rated, how it compares to EDFs, and what to check.

On this page
  1. Units: kgf, newtons and lbf
  2. Static vs in-flight thrust
  3. Thrust-to-weight
  4. Comparing with electric ducted fans
  5. Throttle response
  6. Reading a spec sheet
  7. Safety on the ground
  8. Next steps

A typical sport-jet turbine makes roughly 8 to 14 kgf of thrust, or about 80 to 140 newtons (18 to 31 pounds-force). Smaller turbines start around 2 to 4 kgf. Large scale engines reach 16 to 25 kgf, and the biggest hobby units are around 30 to 50 kgf or more.

Units: kgf, newtons and lbf

Turbine thrust is quoted in three units:

  • kgf (kilogram-force): the force that would hold up a 1 kg mass. Common for model turbines.
  • N (newtons): the SI unit. 1 kgf is about 9.81 N.
  • lbf (pounds-force): the imperial unit. 1 kgf is about 2.2 lbf.

Marketing copy often writes “lbs” for thrust. In this context it means pounds-force, not weight.

Turbine class kgf Newtons Pounds-force
Small 2 to 4 About 20 to 40 N About 4 to 9 lbf
Sport jet 8 to 14 About 80 to 140 N About 18 to 31 lbf
Large scale 16 to 25 About 160 to 250 N About 35 to 55 lbf
Very large 30 to 50+ About 300 to 500+ N About 66 to 110+ lbf

Static vs in-flight thrust

Turbine thrust is usually rated as static thrust at sea level, at around 15 °C. It’s a bench figure. In flight, real thrust falls with heat, altitude and losses in the intake and exhaust ducting. Installation losses inside a fuselage often take a noticeable share, commonly in the 5 to 15 percent range. Plan for installed thrust to be lower than the rating.

Idle thrust is a small fraction of maximum, often somewhere around 3 to 8 percent. Thrust also rises along a curve as the engine spins up, rather than holding a fixed value at every throttle setting.

Thrust-to-weight

Thrust-to-weight ratio tells you how a jet will accelerate and climb. For a typical sport jet, a ratio of roughly 0.7:1 to 1:1 is common. Aerobatic and 3D jets can exceed 1:1. For example, a 10 kg jet with 8 kgf of installed thrust sits at about 0.8:1. Wing loading and drag matter too, so ask experienced pilots about a specific design.

Comparing with electric ducted fans

EDF static thrust depends on fan size, battery and installation. Approximate figures:

  • 70 mm fan on 6S: about 1.5 to 2.5 kg
  • 90 mm fan on 6S to 8S: about 3 to 4.5 kg
  • 120 mm fan on 10S to 14S: about 6 to 10 kg or more

Spec-sheet EDF thrust figures are often optimistic and battery-dependent. An EDF is limited by its battery, while a turbine runs for as long as its fuel lasts. For that trade-off, see RC jet flight time.

Throttle response

Turbines spool up slowly. Going from idle to full thrust usually takes roughly 2 to 5 seconds. Plan approaches and go-arounds with that lag in mind. A flame-out on approach leaves no power for a go-around.

Reading a spec sheet

Before you compare numbers, check:

  • Is the figure static or in flight?
  • Is it in kgf, N or lbf?
  • Is it for the engine alone or the installed system?
  • What were the test conditions, such as temperature, altitude and fuel?
  • Is there an idle figure as well as the maximum?

Safety on the ground

When you run a turbine up to full thrust on the ground, restrain the model or have a helper hold it, and keep everyone out of line with the intake and exhaust. The full start sequence is in how to start an RC jet turbine safely.

Next steps

Thrust feeds into flight time and noise. See how loud RC jet engines are for the noise side. For how thrust is produced inside the engine, see how an RC jet turbine works.

The complete guide to rc jets

RC Jet Engines: Turbines, EDFs and How to Get Started
Read the guide

Keep exploring

Guides from other topics

All topics →