RC Jets

RC Jets with Afterburners: Real Flames vs LED Effects

Most RC jet 'afterburners' are LED lighting effects, not fire. Compare LED kits with real flame afterburners, their risks and safe install basics.

On this page
  1. What “afterburner” usually means on an RC jet
  2. LED afterburner kits
  3. Real flame afterburners
  4. A flame from your turbine is a warning sign
  5. A checklist for adding an LED kit
  6. LED vs real flame at a glance
  7. Next steps

An afterburner is a fighter-jet term. Extra fuel is burned behind the turbine for a short burst of thrust. On RC jets, the word almost always describes a lighting effect that copies the look. This article explains the difference, what LED kits involve, and why real flame is a different category of risk.

What “afterburner” usually means on an RC jet

Most RC jets sold with an “afterburner” use LED lights around the exhaust. It’s a visual effect. The LEDs usually mount around the motor or the rear of the tail cone, often inside a foam or plastic nozzle. Many kits connect to the throttle channel, so the glow brightens as you advance the throttle.

LED afterburner kits

Sizing. Kits are built for specific EDF diameters, from 64 mm and 70 mm up to 90 mm and 120 mm or larger. Some are built around motor can sizes instead. Match the kit to your fan or motor before you buy.

Mounting. The LED ring or board attaches to the rear of the motor housing or a tail cone with clips, glue or zip ties. Make sure it can’t work loose in flight.

Power and wiring. Kits typically draw power either from a small dedicated LiPo or from the receiver and throttle Y-harness, through a controller. Check the kit’s current draw against what your receiver and power system can handle. Route the wires forward through the fuselage, away from moving parts and heat.

Look. Amber, orange and blue are common colours. Some hobbyists paint or line the exhaust tube to make the glow look brighter. Keep any reflective finish clear of heat sources.

Real flame afterburners

A true afterburner injects and burns extra fuel in the exhaust. Some DIY projects have tried it, mostly with butane-fuelled setups. These are rare and experimental, and the gains on small scales are uncertain.

Be aware of several things:

  • Fuel use rises sharply. A real afterburner can multiply fuel burn well beyond normal full power.
  • Fire risk. Flame near the airframe, the field and the pilot is a serious hazard.
  • Thrust gain is small and inconsistent. Reported gains in DIY projects are modest, and the runs are short.
  • Rules. Field and insurance rules may ban open-flame effects.

Treat real-flame afterburners as an advanced experiment, not a bolt-on upgrade.

A flame from your turbine is a warning sign

If your turbine shows flames from the exhaust during a start, that’s a hot start or an over-rich condition, not an afterburner. Abort the start and follow the manual. The steps and warning signs are in how to start an RC jet turbine safely.

Some glow from the exhaust in low light comes from hot metal parts, not flame. That’s normal for a running turbine, and it doesn’t mean the engine is running hard. How the turbine works and why its exhaust runs so hot is explained in how an RC jet turbine works.

A checklist for adding an LED kit

  1. Match the kit to your EDF diameter or motor size.
  2. Mount it so it doesn’t block cooling air or the exhaust path.
  3. Route the wires away from hot exhaust and moving parts, and secure them.
  4. Power the kit the way the maker specifies, and don’t overload the receiver.
  5. Test on the ground with the throttle through its full range before you fly.
  6. Check your club’s rules. Some sites allow LED effects but restrict anything involving an open flame.

LED vs real flame at a glance

LED afterburner kit Real flame afterburner
What it is A lighting effect Extra fuel burned in the exhaust
Where you’ll see it Common on EDF scale jets Rare, experimental DIY projects
Thrust gain None Small and inconsistent
Fire risk Low, with normal wiring care High
Fuel use No change Sharply higher
Field rules Usually acceptable; check first Often restricted; check first

Next steps

Read RC jet engines: turbines, EDFs and how to get started to see where a lit-up EDF jet fits among the options. If you’re thinking about a turbine, the start guide is the next read.

The complete guide to rc jets

RC Jet Engines: Turbines, EDFs and How to Get Started
Read the guide

Keep exploring

Guides from other topics

All topics →