RC Jets

How an RC Jet Turbine Works (With Diagram)

Learn how an RC jet turbine works, step by step: the airflow path, compressor, combustor and turbine, plus the fuel system and ECU that control it.

On this page
  1. How does an RC jet turbine work?
  2. Airflow from front to back
  3. The main parts
  4. Why the numbers are so high
  5. The fuel path
  6. Common misconceptions
  7. Safety: the plane of rotation
  8. Where to go next

A model jet turbine looks complicated, but it does four jobs in order: it takes in air, squeezes it, burns fuel in it, and pushes the hot gas out the back. Most of the parts exist to make those steps happen reliably at very high speed.

How does an RC jet turbine work?

A model turbine runs the same basic cycle as a full-size jet engine, often called the Brayton cycle: intake, compression, combustion, expansion and exhaust. Air is squeezed by a spinning compressor, mixed with fuel and burned. The hot gas then passes through a turbine wheel, which drives the compressor through a shared shaft. The gas that leaves the nozzle at high speed is the thrust.

Airflow from front to back

AIR IN
   |
   v
+------------+      +------------+      +------------+
| COMPRESSOR | ---> | COMBUSTOR  | ---> |  TURBINE   | ---> EXHAUST = THRUST
+------------+      +------------+      +------------+
       ^                                       |
       |_______________ SHAFT _________________|
  1. Intake: air enters through a smooth bellmouth at the front.
  2. Compressor: a single centrifugal wheel spins the air outward and squeezes it.
  3. Diffuser: fixed vanes slow the air and convert its speed into pressure.
  4. Combustor: fuel is vaporised or sprayed into the air and ignited.
  5. Nozzle guide vanes: fixed vanes aim the hot gas onto the turbine wheel.
  6. Turbine wheel: the hot gas spins it, and the shaft drives the compressor.
  7. Exhaust nozzle: the remaining gas leaves at high speed and makes thrust.

The main parts

Compressor. Usually one centrifugal (radial) wheel, often machined from aluminium. It raises the pressure of the incoming air before it reaches the combustor.

Diffuser. A ring of fixed vanes that slows the air and recovers pressure, so the combustor gets a steadier flow.

Combustor. Most model turbines use an annular, ring-shaped chamber. Only part of the air is used for combustion. The rest cools the hot parts and mixes with the burned gas.

Nozzle guide vanes. A fixed ring of vanes that directs the hot gas onto the turbine wheel at the right angle.

Turbine wheel. A single axial wheel, usually cast from a nickel superalloy such as Inconel 713C. It has to survive high temperature and very large centrifugal forces.

Shaft and bearings. One shaft joins the turbine and compressor. It typically runs on two small ceramic-hybrid ball bearings, which are lubricated by turbine oil mixed into the fuel.

Starter and igniter. An electric starter spins the shaft up, and a glow plug or igniter lights the fuel. Modern engines start on kerosene rather than a separate start gas.

Electronic control unit (ECU). The ECU controls the fuel pump and valves, reads RPM and exhaust gas temperature (EGT), and runs the start, run and shutdown sequence.

Why the numbers are so high

Turbine wheels are small and light, so they spin very fast. Shaft speed at full power is roughly 100,000 to 240,000 RPM, depending on engine size, and idle is tens of thousands of RPM. Exact figures vary by engine, so check the manual for yours.

Exhaust gas temperature at full power is often around 550 to 750 °C. EGT can climb sharply during a bad start, which is why the ECU watches it closely. EGT is measured after the turbine, so the hottest part of the combustor runs hotter than the number on the display.

At these speeds, balance and tolerances are critical. An unbalanced rotor can destroy the engine, so bearings and rotor work belong to the maker or a qualified technician. See RC jet engine maintenance.

Turbines also don’t respond instantly. Going from idle to full thrust usually takes about 2 to 5 seconds, which matters on approach and go-arounds.

The fuel path

Fuel moves from the tank to a hopper or air-trap tank, through a filter, then to the pump, a solenoid valve and the engine. The hopper keeps a supply at the pump even during manoeuvres, so air bubbles don’t reach the pump. Fuel and oil choices are in what fuel RC jet engines use.

Common misconceptions

  • Model turbines are not scaled-down airliner engines. Nearly all use a single centrifugal compressor stage.
  • Thrust doesn’t come mainly from burning fuel at the exhaust. It comes from accelerating a large mass of air through the engine.
  • The turbine wheel doesn’t drive a fan in typical model jets. It drives the compressor, and the nozzle provides the thrust.
  • EGT isn’t the combustor temperature. The combustor core runs hotter than the exhaust reading.

Safety: the plane of rotation

The plane of rotation of the turbine wheel is the danger zone. A failed wheel can throw parts outward, so never stand in line with the turbine. Wear hearing and eye protection, and keep a CO2 fire extinguisher within reach. Noise levels are covered in how loud RC jet engines are.

Where to go next

The complete guide to rc jets

RC Jet Engines: Turbines, EDFs and How to Get Started
Read the guide

Keep exploring

Guides from other topics

All topics →