Learn to Fly

How to Land an RC Plane: A Beginner's Step-by-Step Guide

Learn to land an RC plane step by step: flying the pattern, managing descent, lining up on final, flaring, crosswinds, and when to go around.

On this page
  1. Before you land
  2. Fly the pattern
  3. Control your descent
  4. Line up on final
  5. Flare and touch down
  6. Taildraggers and gearless foam planes
  7. Crosswind landings
  8. When to go around
  9. Practice landings safely
  10. Common landing mistakes
  11. Safety
  12. Next steps

To land an RC plane, fly into the wind, follow a rectangular pattern, descend on a shallow glide with some power still on, and flare just before the wheels touch. If the approach looks wrong at any point, go around and try again. A go-around is a normal part of flying.

Before you land

  • Check the wind before you fly the pattern. Landing into the wind reduces your ground speed at touchdown.
  • Plan your pattern around fixed landmarks, such as a field edge, a runway edge, or a line of trees.
  • Keep a battery reserve. Many pilots aim to land with about 20 to 30 percent of the pack left. For LiPo packs, don’t let a cell drop below about 3.5 volts at rest.

Fly the pattern

The landing part of the pattern has three legs:

  1. Downwind: Fly parallel to the runway, opposite the direction you will land, at a safe height.
  2. Base: Turn gently, with a shallow bank, toward the runway.
  3. Final: Line up with the runway and descend on a steady glide.

Keep the turns shallow. Low, slow, steep turns are a common cause of stalls and spins.

Control your descent

  • Reduce the throttle on downwind to start a gradual descent.
  • Use the throttle to manage the descent rate. Adding a little power can flatten or slow the drop. Many instructors teach that the throttle controls descent and the elevator controls airspeed, though teaching methods vary.
  • Keep some power on through final. Cutting the throttle too early can leave you short of the runway or cause a stall.
  • Keep your airspeed well above the stall speed throughout the approach.

Line up on final

Make small corrections early, while the plane is still high. Avoid large corrections close to the ground, because they tend to make the plane unstable. If you find yourself badly lined up, go around.

Flare and touch down

  • Flare at about 1 to 2 feet (30 to 60 cm) above the ground. Apply gradual up-elevator to raise the nose and bleed off speed.
  • On a tricycle-gear plane, the main wheels should touch first, with the nose wheel following.
  • Bring the throttle to idle at or just before touchdown, and track straight with the rudder.

Two common mistakes:

  • Pointing the nose down to land. Diving adds speed and can cause the plane to float or bounce.
  • Pulling up hard just before touchdown. An abrupt flare can balloon the plane or stall it.

Taildraggers and gearless foam planes

Taildraggers land on three points or on the main wheels, depending on the model. Gearless foam planes often belly-land on grass. Cut the throttle before the plane touches down to protect the propeller and motor.

Crosswind landings

In a crosswind, crab into the wind on final. That means angling the nose slightly into the wind so the plane still tracks straight over the runway. Just before touchdown, straighten the nose with rudder so the wheels meet the ground pointing straight ahead.

When to go around

Go around if the approach is too high, too fast, or misaligned. Add throttle smoothly, climb, and fly the pattern again. A go-around is not a failure. You can try again as long as you have battery reserve for another circuit.

Practice landings safely

  • Use a simulator to practice the pattern and touchdowns. See RC flight simulators compared.
  • Practice low passes and touch-and-goes with an instructor on a buddy box.
  • Check your trainer’s manual for slow or assisted modes. Some stabilized trainers offer them.

Common landing mistakes

  • Cutting the throttle too early.
  • Flaring too late, or pulling up too hard.
  • Making big corrections close to the ground.
  • Feeling you must land on the first try. Going around is normal.

Safety

Never land toward the pilot station, pits, or spectators. At club fields, call “landing” so others know to clear the runway. Keep people clear of the landing area and the approach path.

Next steps

For the start of every flight, read how to take off an RC plane. For the full learning path, see how to fly an RC plane.

The complete guide to learn to fly

How to Fly an RC Plane: A Beginner's Tutorial
Read the guide

Keep exploring

Guides from other topics

All topics →